VARTA Storage GmbH VARTA pulse 3 Instruction Manual Download Page 58

Page: 58 / 146

Subject to modification! Updated 12/2017

Warranty registration

8.5

This online-based warranty registration consists of two parts:

Part 1: Registration of the energy storage system by the installation

engineer incl. commissioning report (Chapter 8.5.1)

Part 2: Warranty registration by the end customer incl. registration

for the web portal (Chapter 8.5.2)

Warranty registration by the installation engineer

8.5.1

Open page

www.varta-storage.com

Change to "energy storage systems"



Registration in the B2B area with login and password



On the welcome page, click on "Start VARTA-Portal"
Change to "energy storage registration"

Entering the data for the battery storage:



Initial installation/retrofit,



Date,



Installation engineer,



Serial number,



Activation code,

Summary of Contents for VARTA pulse 3



















































































































































Search results

Summary of Contents for VARTA pulse 3

Reviews:

VARTA Storage GmbH VARTA pulse 3, Instruction Manual, Page: 58 / 146

Search results

Summary of Contents for VARTA pulse 3

Reviews: