Lucina MaX
/
Dorotha
5)
Refit the two covers. Place the top plastic c
over
1
sideways under the engine plate, lock it, and tighten the plastic
nut
3
.
Bend the bottom plastic
cover
2
upwards and place the cover opening on the
protrusion/foot
4
of the frame. Release the
cover deflection, and the cover snaps into place.
Make sure the cable harness is not damaged, and connectors are firmly connected together.
2.4.3 W
ORKING
WITH
THE
M
ACHINE
2.4.3.1 T
HE
M
ACHINE
W
ORKING
W
IDTH
It is always necessary to adjust the working width to the growth density!
We do not recommend using the maximum working width (see
) given by the disc design. The operator cannot lead the
machine in the terrain sufficiently straight and accurately to cut the growth over the disc’s full working width. We recommend guiding the
machine through partially (approximately 5-10 cm from the front cover edge) mowed growth (marked by the arrow in
Pict. 6
from the
operator’s view).
2.4.3.2 G
ROWTH
C
UTTING
M
ETHOD
The growth must be free of solid items (such as stones, wires, loose debris, etc.) before using the machine. These
items could be thrown out or could damage the machine. If they cannot be removed, avoid such spots.
When mowing in uneven terrain, care must be taken to ensure that the bottom disc continuously slides over the ground and does not
bounce. Disc bouncing results in a low-quality of growth mowing and uneven stubble.
Set the maximum engine speed, let the cutting disc spin at its maximum speed, and then drive against the growth that you wish to
mow. The mowed growth is ejected by the cutting disc to the right, on the side cover that defines rows.
While mowing, proceed through the growth so that the non-mowed growth is always left of the machine
(Pict. 6).
The covers are designed to fully control the mowed growth flow even when the full working width is used.
When mowing on slopes, it is best to ride along the slope contour lines.
Observe the safe slope access, please
If the cut growth is very dense, prickly, rotten or beaten, it is necessary to reduce the machine’s working width proportionally in such a
way that there is no significant reduction in cutting disk speed and thus reduced mowing quality.
2.4.3.2.1 M
OWING
T
ROUBLES
Pay special caution when lifting and backing the machine!
The engine must always be OFF when cleaning the area under the top cover!
Always only tilt the machine backwards by pushing the handlebar downwards.
Always pay extra caution when moving
in the area under the raised machine! Secure it against spontaneous movement!
Take extra care when cleaning the space underneath the top cover. Blade cutting edges are sharp. When
cleaning, protect your hands with work gloves or use a suitable item, such as a tree branch.
Always wait for the cutting disc to stop before proceeding with any activity on or around the machine.
1.
The disc loses speed, the engine loses speed, but does not stop.
Immediately stop the machine travel and slightly back-up with the machine front gently lifted (pushing the handlebar
downwards). The space underneath the top cover partially cleans itself from the excessive grass mass. Then move again
against the growth.
2.
The drive stopped, the engine turned OFF.
Release both levers on the handlebars and lift the front of the machine by pushing on the handlebars. Slide the machine
slightly backward. Clean the area under the top cover and spread the grass mass on the surface. Start the engine, turn
on the cutting disk drive, and start moving against the growth.
2.4.4 R
EPLACEMENT
OF
A
CCESSORIES
- R
ECONFIGURATION
Only the brush cutters with trade name
BDR-620D
allow replacing their cutting discs with
other adapters.
The brush cutters
Lucina
,
Lucina 65
, and
Dorotha
whose type designations also start with
BDR-620D
are only
single-purpose machines and
are not designed for any adapter changes
.
The brush cutter’s
Lucina MaX
default adapter mounted to its chassis is
MaX
its cutting disc. It must be removed before any
accessory change.
Prepare, if possible,
2 spanners
No. 10 and
2 ring spanners
No. 13, and a box for fastening material to be used
later.
Always turn OFF the engine and wait for the work tool to completely stop before performing any work in the close
vicinity of the machine!
Disconnect the ignition spark plug cable.
81
The sticker is attached to the left side of the cutting disc safety cover.
82
For quick installation, we recommend preparing, instead of 2 ring spanners, 1 ring spanner No. 13 and 1 ratchet (GOLA) with socket size 13.
26
R
ev
iz
e
1
0
/2
0
2
0
