Lucina MaX
/
Dorotha
starts moving smoothly) to the wheels
15
. The clutch gearbox is covered with the plastic
gearbox cover
13
. At the front, there is the
cutting disk
4
with four
steel blades
5
. The operator is protected against flying cut growth items by a sheet metal
cover
(
1
and
10
) of the cutting disk, meeting EN 12733. The mowed growth spacing is secured through the removable
side cover
3
, which is
attached by its
screw connection
9
.
1
Cutting disk top cover
6
Drive cover
11
Machine frame
16
Handle
2
Front handle
7
Bolt
12
Tank cap
17
Disk drive clutch lever
3
Side cover with a
holder
8
Engine/Battery
13
Gearbox cover
18
Lock button
4
Cutting disk
9
Side cover screw
14
Strap with cables
19
Travel clutch lever
5
Blade (4 pcs)
10
Cutting disk bottom cover
15
Wheels
20A
Accelerator lever
20B
Starter panel
Table 17: Legend to Pict. 2
2.4 O
PERATING
I
NSTRUCTIONS
2.4.1 M
ACHINE
A
SSEMBLY
Request the machine unpacking and training from your seller as a part of his pre-sale service!
Gripping points for unpacking from the box (per
Pict. 1
): grab the cutting disk at the front or use hole under the gearbox cover, and the
machine frame tube in the rear.
1
Folded handlebars
5
Flap long and short
2
Battery - BDR-620DBiS only
6
Charger - BDR-620DBiS only
3
Cutting disk top cover
7
Flap holder
4
Package with small parts
8
Left (lower) additional disc cover
Table 18: Legend to Pict. 1
2.4.1.1 M
ACHINE
A
SSEMBLY
P
ROCEDURE
Assemble the machine per the following procedure:
(We recommend that the machine assembly is completed by two persons .)
Instructions regarding right/left directions are given from the operator’s view.
1. Following
Pict. 1
- remove both the disc cover parts
3
, bag
4
with small parts, side and rear cloth
5
, flap holder,
7
and the
left additional cover
8
from the box. For electric starter machines, remove the battery
2
and charger
6
from the box. Remove
the cardboard insert between the handlebars and the engine from the box.
2. Grab the machine, using its gripping points at the front and in the back and remove it from the box.
3. Lift the handlebars
1
per
Pict. 1
, turn them, and attach them per
Pict. 9
step
> 1
to the frame (select one of the 3 holes in the
height-adjusting handlebars and one of the two holes in the frame). Following
> 1
, pass the screw through, attach the flat
washer, and firmly tighten the handlebars with the wing nut.
The bowden cables of the control levers must not be crossed
- this would reduce their service life!
Remove 2 pcs of the tightening straps from the bag and attach the bowden cables to the handlebars at the top end of
the handlebar tube bend. To fasten, 2 strapping tapes are sufficient. Cut the loose ends of the straps.
4. Following
Pict. 9
>2 ,
attach the bottom disk cover
2
to the left side of the frame and fasten it by 4 screws
B
. Tighten the
screws.
5. Following
Pict. 9
>3 ,
fit the screw
B
into the hole in the right rear part of the frame, but do not tighten it. Insert the right
(bigger) part of the cover
3
between the bottom plastic cover of the disk and machine frame, so the screws
B
and
C
in the
frame fit into the three grooves in the cover marked with an arrow. Manually tighten the screw connection
B
. Do not tighten the
screw connection
C
for the time being. Attach the right side of the cover by three screws
B
per
>4
. Manually tighten the screw
connection
B
per
>4
.
6. Following
Pict. 9
>5 ,
insert a screw
B
into the rear part hole and slide the smaller left part of the cover towards the frame from
the machine’s left side and fasten it with two screws
B
per
>6
. Manually tighten the screws
B
. Connect both halves of the
cover together in the front section per
>6
by means of the two connections
D
. Tighten the screw connection
D
.
7. Remove the strap (cloth) from the bag and attach it from the left side to the left-hand cover using a screw connection
F
following
Pict. 9
>7
. Place the nut with the washer on the opposite side of the cover other than the strap. Tighten the screw connection
F
so that it moves freely with the loop.
8. Always tighten all screw connections
B
and
C
marked with an arrow per
> 9
!
9. On the shorter flap arm holder (
9
per
Pict. 1
), insert per
Pict. 9
step
> 8
the rear (shorter) side cloth
7
and on the longer flap
arm holder, insert the side (longer) cloth
6
. Pull the strapping tapes
E
through the cover holder holes and secure both covers
6
and
7
against sliding by tightening the tapes E. Please shorten the loose ends of the tapes.
10. First, loosen the mounting bolt of the side cover,
9
so
Pict. 9
it is possible, per
Pict. 9
> 8
smoothly insert the shorter cover
beam arm into the frame opening. Tighten the mounting bolt and make sure the side cover cannot spontaneously fall out.
2.4.2 C
OMMISSIONING
First, carefully read the instructions
for the use of the motor! This way, you will prevent its potential
damage.
72
The original operating instructions and their Czech translation are attached to the machine.
23
R
ev
iz
e
1
0
/2
0
2
0
