manualshive.com logo in svg

Vari Lite VL2B, Service Manual, Page: 93 / 310

Share
Download
Vari Lite VL2B Service Manual Download Page 93

C

HAPTER 

3.  M

AINTENANCE 

P

ROCEDURES

3-47

02.9631.0010

CONFIDENTIAL

15 Jan 98

6-32X5/8"PPZ SCREW

6-32 KEPS NUT

TIE WRAP SADDLE

2-56 NUT

BFBVIEW

6-32 X 5/8"PPB

SCREW

2-56X3/8"PPZ SCREW

Figure 3-4.  Brightness/Filter Bulkhead Sensor Switch Removal and Replacement

Step 6.

Remove brightness iris.

a. At brightness iris, remove three 6-32x5/8"PPZ screws and

#6 flat washers that secure brightness iris to bulkhead,
remove belt, and remove brightness iris.

Step 7.

Install replacement brightness iris and re-assemble luminaire.

a. Install replacement brightness iris on front of

brightness/focus bulkhead and open iris.

b. Align three holes in brightness iris to holes in three black

grommets in bulkhead.  For correct alignment of sensor pin
on iris, place sensor stop opposite brass hole plug.

c. Put #6 flat washer on each 6-32x5/8"PPZ screw and apply

Loctite 242 to screws.

d. Insert screws into iris assembly and grommets and partially

thread screws.  Do not fully tighten screws.

e. Place 0.05 inch spacer between brightness iris and bulkhead

and fully tighten screws.  Space must be maintained to
prevent grommets from rubbing against inside of iris.

f.

Install timing belt on iris pulley and then place around
pulley.

Summary of Contents for VL2B























































































































































































































































































































Reviews:

No comments