manualshive.com logo in svg

Vari Lite VL2B, Service Manual, Page: 157 / 310

Share
Download
Vari Lite VL2B Service Manual Download Page 157

C

HAPTER 

3.  M

AINTENANCE 

P

ROCEDURES

3-111

02.9631.0010

CONFIDENTIAL

15 Jan 98

3.3.18  Input/Output Connector Removal and Replacement

Parts:

1 EA

RECEPT, 9POS CHASSIS MNT LAMP (52.6251.0001)

Tools:

Screwdriver, Phillips #1
Screwdriver, Phillips #2
Pin removal tool
1/4” nut driver

To remove and replace input/output connector, (Figure 3-38):

4-40 KEPS NUT

4-40X5/16"PPB SCREW

INPUT/OUTPUT

CONNECTOR

KEYING

CONNEXP

Figure 3-38.  Input/Output Connector Removal and Replacement

Step 1.

Remove power to luminaire.

Step 2.

Open chassis lid.

a. At electronics chassis, remove six 10-32x3/8"PPB screws

that secure chassis lid to chassis and open lid.

Step 3.

Remove input/output connector nine-pin receptacle from

chassis.

a. At connector, at outside of chassis, using #1 Phillips

screwdriver and 1/4” nut driver, remove four
4-40x5/16"PPB screws and 4-40 KEPS nuts that secure
square flange receptacle (I/O connector) to chassis.

b.   Using pin removal tool, remove pin contacts from faulty

receptacle and remove receptacle.

Summary of Contents for VL2B























































































































































































































































































































Reviews:

No comments