Vanco RS232-IP Manual Download Page 8 | Manualshive

Page: 8 / 24

background image

www.vanco1.com

800-626-6445

8

CONNECT AND OPERATE

There are 4 methods that can be used to connect to the RS232-IP:

•  Ethernet to Serial (RS232-IP connected directly to a network with a Cat5e/6 cable)
•  Wifi (Client) to Serial
•  Wifi (Access Point) to Serial
•  Default (combination of any the above-mentioned modes)

Connect and Operate - Ethernet to Serial:

In this mode, LAN is enabled and WIFI/WAN functions and ports are closed. Through the appropriate settings, the

data between the computer and the LAN port on the RS232-IP can be achieved through the network through category

cables. Ethernet can be configured as a dynamic IP address (DHCP) or can also be configured as a static IP address

(STATIC).

«
...
6
7
8
9
10
...
»

Summary of Contents for RS232-IP

























Reviews:

No comments

Related manuals for RS232-IP

Brand: Uebo Pages: 4

Brand: JED Pages: 4

Brand: B&B Electronics Pages: 73

Brand: B&B Electronics Pages: 4

Brand: Tascam Pages: 35

Brand: Lenze Pages: 132

Brand: Datalogic Pages: 2

ENC58-H15 Series

Brand: Datalogic Pages: 2

Brand: Midian Pages: 28

Brand: All-Power Pages: 35

Brand: IRiver Pages: 33

Brand: B&B Electronics Pages: 3

Brand: Lika Pages: 2

Slimline Plus 1250

Brand: Wagan Pages: 32

Brand: HEIDENHAIN Pages: 44

Brand: Heitronic Pages: 8

Brand: Intech Pages: 4

Atlona OmniStream 122

Brand: Panduit Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands