Vanco RS232-IP Manual Download Page 14 | Manualshive

Page: 14 / 24

background image

www.vanco1.com

800-626-6445

14

Default Mode

In this mode, WIFI is enabled as well as the WAN and LAN ports are enabled. The RS232-IP also can work in the AP

(access point) mode. This setting allows elements from all the modes to be used and set up accordingly, and can even

act as a wireless/wired Ethernet router. WIFI device(s) can connect with the RS232-IP, and become one device within

the associated network. WAN default IP is dynamic IP address.

«
...
12
13
14
15
16
...
»

Summary of Contents for RS232-IP

























Reviews:

No comments

Related manuals for RS232-IP

Brand: YOKOGAWA Pages: 58

Brand: Omega Digitech Pages: 8

Brand: µ-Dimension Pages: 6

Brand: Sylvania Pages: 28

Brand: Black Box Pages: 60

Varispeed CIMR-G7A

Brand: YASKAWA Pages: 459

Brand: M-system Pages: 5

SO SPEAKY HDMI+ SK5

Brand: DANE-ELEC Pages: 16

Brand: Hall Research Technologies Pages: 8

Brand: Sinexcel Pages: 49

Brand: Manhattan Pages: 2

Brand: Icy Box Pages: 16

Nelson LINK DAC III

Brand: MSB Technology Pages: 12

Brand: Uhlenbrock Elektronik Pages: 4

Brand: AV Access Pages: 20

Brand: ETQ Pages: 32

Brand: Woodpecker Pages: 22

Brand: CORNING Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands