background image

13 of 23  

7.

 

APPLIANCE PREPARATION 

7.1.

 

 Window Removal 

See figure 12. 

 

Turn the top three spring loaded window bolts through 90

0

 to release the window 

from the firebox. 

 

Remove the bottom three spring-loaded window bolts. 

 

Detach the chain from the top right corner of the window. 

 

Carefully lift the window away. Keep the window and bolts in a safe place. 

 

7.2.

 

Ignition Spark Check 

The pilot burner and electrode unit is at the left end of the burner. 
Push in the lighting knob and turn counter-clockwise through the “IGN” position to 
“PILOT”. A spark should flash across from the pilot electrode to the pilot burner shield. 
See figure 13.  
  

7.3.

 

Flame Control Motor Check 

See figure 14. 

 

Fit the battery holder to the 

black 

connector pad.

 

 

 

Fit the four batteries into the holder.  

 

Fit the two “L” terminals to the tabs at the left side of the control unit 

 

Connect the switch unit to the wire harness. 

 

Operate the switch. Pressing one side of the switch should cause the flame control knob to rotate counterclockwise. 
Pressing the other side should cause clockwise rotation. 

 

Disconnect after checking.   

 

 

Figure 14 Flame control motor check 

 

 

Figure 13 Ignition spark check 

Figure 12 Window removal 

Summary of Contents for HORIZON 535

























Reviews: