background image

Algorithm

Description

Processing options

• Azimuth averaging: 2 ... 1024 pulses
• Corrections for gaseous attenuation and1/R2
• Dual-polarization: Alternating, Simultaneous, H-only, V-only
• Clutter filters: Fixed/Adaptive GMAP in frequency domain, or IIR

time domain

• High sensitivity Rhv STAR mode processing: >3dB improvement in

detectability

• Pulse integration up to1024
• Range de-aliasing: random phase
• Scan angle synchronization for data acquisition
• Up to 4 pulse widths
• Velocity de-aliasing: dual PRF velocity unfolding at 2:3, 3:4, and 4:5

for 2X, 3X, or 4X velocity unfoldings

Data outputs (8 and 16 bit)

Zh

Zv

Zhv

V

W

SQI

ZDR

LDR

RHOHV

PHIDP

, and 

KDP

Optional data outputs

HCLASS

I

/

Q

Data quality thresholds

• Signal-to-noise ratio (SNR)—Used to reject bins having weak

signals; typically applied to dBZ

• Signal quality index (SQI)—Used to reject bins having incoherent

signals; typically applied to mean velocity and width

• Clutter-to-signal ratio (CSR)—Used to reject range bins having very

strong clutter; typically applied to mean velocity, width, and dBZ

• Speckle Filter—Removes single-bin targets such as aircraft or noise

and fills isolated missing pixels

4.2 RVP10 Input and output summary

Table 12 I/O summary

Function

Description

AZ

/

EL

 angle input options • Serial 

AZ

/

EL

 angle tag input using standard Vaisala RCP format

• 16-bit each parallel TTL binary angles through the I/O-62 card
• Synchro angle inputs through the I/O-62 card
• RCP network antenna packet protocol

Ethernet I/O from host
computer

Data output of calibrated 

dBZ

V

, and 

W

 during normal operation.

Full 

I

/

Q

 time series recording with a separate tsarchive utility, or

through a custom application using a public API. Signal processor
configuration and verification read-back is performed through the
Ethernet interface.

Input from IFDR

• 32-bit floating point 

I

/

Q

 values

• Optional dual-channel 

I

/

Q

 samples (for example, for polarization

systems or dual-frequency systems)

RVP10 Hardware Quick Guide

M212758EN-A

22

RESTRICTED

Summary of Contents for RVP10



































Reviews: