Vaderstad E-services Instructions Manual Download Page 38

Page: 38 / 48

Alarm list

221. WorkStation 1 not connected

If Gateway loses contact with
WorkStation 1 during operation:

Check the cabling between Gateway and WorkStation.

Check that the cable is not trapped or otherwise damaged.

Check the condition of the connectors.

If the machine has a WS2 —check the connector on WS2

231. WorkStation 2 not connected

If Gateway loses contact with
WorkStation 1 during operation:

See alarm no 221

250. Seed level sensor

Check the sensor’s cable, contacts and connections.

260. Grass seed level sensor
(BioDrill)

Check the sensor’s cable, contacts and connections.

270. Interruption to communication

For some unknown reason Gateway has lost communication with the terminal,
e.g. if the terminal has been switched off or the iPad has been out of Wi-Fi
range. Acknowledge the alarm in the alarms menu. Feed stops.

If the fault recurs.

Check the cabling for supply voltage to the terminal and the cabling between
Gateway and the terminal.

If the iPad is not communicating with the dock, check whether Bluetooth is
enabled.

281. Rotation guard, fertiliser LH

If the metering units do not move:

Check connections and connectors to the tramline coupling.

If the alarm appears despite the
metering units rotating:

Check the sensor. The sensor is located in the tramline coupling, could be
defective.

Check that the roller in the coupling is rotating with the feed shaft. The roller
should rotate when tramlining is off.

282. Rotation guard, fertiliser RH

See alarm no 281

283. Rotation guard, fertiliser LH
and RH

See alarm no 281

290. Hydraulic motor, fertiliser

See alarm no. 40

300. Low level, fertiliser

Check the fertiliser level in the hopper.

If there is fertiliser in the hopper:

The sensitivity of the sensor has been incorrectly set.

310. Fertiliser valve, max power

Perform a new calibration

Check the oil flow rate

320. Hopper level alarm, fertiliser

Check the sensor’s cable, contacts and connections.

451. Fertiliser tramlining LH

Check the sensor’s cable, contacts and connections.

Check the sensor.

452. Fertiliser tramlining RH

See alarm no. 451

903099-en-gb; 19.01.2021

Summary of Contents for E-services

















































Search results

Summary of Contents for E-services

Reviews:

Related manuals for E-services

Brands by name

Popular brands

Vaderstad E-services, Instructions Manual

Search results

Summary of Contents for E-services

Reviews:

Related manuals for E-services

Brands by name

Popular brands