Vaderstad E-services Instructions Manual Download Page 36 | Manualshive

Page: 36 / 48

background image

12

Alarm list

21. Seed feed rotation LH

If the metering units do not move:

Check that the toothed coupling between the hydraulic motor and the feed
shaft is in the correct position and intact.

If the alarm appears although the
seed meters:

Check the alert time that has been programmed.

Check the sensor. The sensor is
located in the tramline coupling:

Check connections and connectors to the tramline coupling.

The sensor in the coupling could be defective.

The coupling could be defective. Check that the roller in the coupling is
rotating with the feed shaft. The roller should rotate when tramlining is off.

22. Seed feed rotation RH

If the metering units do not move:

Check that the toothed coupling between the hydraulic motor and the feed
shaft is in the correct position and intact.

If the alarm appears although the
seed meters:

Check the alert time that has been programmed.

23. Seed feed rotation LH and RH

If the metering units do not move:

Check that the toothed coupling between the hydraulic motor and the feed
shaft is in the correct position and intact.

If the alarm appears although the
seed meters:

Check the alert time that has been programmed.

Check the sensor. The sensor is
located in the tramline coupling:

Check connections and connectors to the tramline coupling.

The sensor in the coupling could be defective.

The coupling could be defective. Check that the roller in the coupling is
rotating with the feed shaft. The roller should rotate when tramlining is off.

31. Seed feed BioDrill Rotation LH

If BioDrill is not in use:

Turn off the alarm function. Go to the programming menu on the control unit
and switch off BioDrill.

If the metering units do not move:

Check that the toothed coupling between the hydraulic motor and the feed
shaft is in the correct position and intact.

If the alarm appears although the
seed meters:

Check the alert time that has been programmed.

Check the cables, contacts and connection.

Check the operation of the sensor. The sensor LED should light when the
toothed plate passes. The distance between the sensor and the pulse disc must
be 1–2 mm. Adjust if necessary. An illuminated diode is no guarantee that the
sensor is working properly.

Check the condition and installation of the toothed plate.

32. Seed feed, BioDrill rotation RH

If BioDrill is not in use:

See alarm no. 31

32

903099-en-gb; 19.01.2021

«
...
34
35
36
37
38
...
»

Summary of Contents for E-services

















































Reviews:

No comments

Related manuals for E-services

Brand: Kapriol Pages: 32

Brand: JABO Pages: 4

Brand: KaVo Pages: 13

Brand: vc999 Pages: 52

Brand: Raven Pages: 17

Brand: Campbell Pages: 12

BOMAG BW 100 ADM-5

Brand: Fayat Pages: 216

Brand: B medical systems Pages: 28

Brand: NanoVibronix Pages: 2

Brand: NanoVibronix Pages: 32

Shapes Hexagons

Brand: Nanoleaf Pages: 27

Brand: P-Q Controls Pages: 5

Brand: P+L Systems Pages: 2

Brand: Parker Pages: 64

Brand: Parker Pages: 40

Matrx Digital MDM

Brand: Parker Pages: 20

SHAKER KEEPER 20V 200

Brand: Garland Pages: 84

Brand: Irwin Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands