Vaderstad CR 1225 Instructions Manual Download Page 27 | Manualshive

Page: 27 / 58

background image

Figure 6.16

4. The transport lock will now open, see also

Transport lock“

Figure 6.17

Figure 6.18

Figure 6.19

5. Slowly reverse the tractor until the roller has been

completely folded out, see

“Figure 6.17 “

to

.

Figure 6.20

6. Completely retract the front tool in order to fold the

machine.

Figure 6.21

7. Make sure that sleeve (D) has been adjusted correctly

and that limit switch (E) has been activated. If E has
not been activated, it will not be possible to unfold
the machine. See

“8.4 Setting the depth stopper“

.

D

E

903815-en-gb; 23.09.2021

23

«
...
25
26
27
28
29
...
»

Summary of Contents for CR 1225



























































Reviews:

No comments

Related manuals for CR 1225

Brand: ACCU-CHECK Pages: 104

Brand: idi Pages: 20

Brand: G&G Pages: 2

Brand: H&S Pages: 46

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brand: Hadeco Pages: 72

Brand: LAZBOY Pages: 9

Brand: M-Audio Pages: 3

Web Riderz MM00124 Web Swing

Brand: M&M Sales Enterprises Pages: 2

Brand: Dantel Pages: 22

Brand: Waves Pages: 8

Haymakers Hooimakers F80-350V

Brand: Falcon Pages: 38

Brand: Lightronics Pages: 6

Brand: Neopost Pages: 10

Brand: KAM Pages: 8

Magnetic Rail System Premium

Brand: Geovent Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands