Vaderstad CR 1225 Instructions Manual Download Page 48

Page: 48 / 58

9.10.2

Re-tightening of wheel nuts

Figure 9.22

Following 10–15 km of road transportation, retighten the
wheel nuts. Retighten the nuts in the same way after any
wheel changes. Tighten the nuts using a torque wrench.

Hjul

Åtdragningsmo-

ment

Antal

hjulmuttrar

400/60 x 15

300 Nm (33

kpm).

520/50 x 15

550 Nm (33

kpm).

9.10.3

Tyres and air pressure

Check the tyre pressure. See recommendations in

“Table

9.2 “

Table 9.2

Modell

Transporthjul

bar

kPa

CR 925

4.0–4.5

400

CR 1225

4.0–4.5

400

9.11

Brakes

Adjustment of the brakes should be done while
the tractor hitched to the machine

9.11.1

General

If the brakes are not adjusted, the braking effect
will reduce over time, to the point where the
brakes will cease to function altogether.

It is vital that correct brake adjustment is verified when
the machine is new, and subsequently twice a year.

9.11.2

Hydraulic brakes

If, after adjustment, the brake lever (B) achieves
a vertical position, the brake shoes must be
replaced.

Figure 9.23 Carrier 925/Carrier XL 925

903815-en-gb; 23.09.2021

Summary of Contents for CR 1225



























































Search results

Summary of Contents for CR 1225

Reviews:

Related manuals for CR 1225

Brands by name

Popular brands

Vaderstad CR 1225, Instructions Manual

Search results

Summary of Contents for CR 1225

Reviews:

Related manuals for CR 1225

Brands by name

Popular brands