vacuubrand MV 10C VARIO select Instructions For Use Manual Download Page 20

Page: 20 / 88

20901115_12+16C_VARIO_sel_V1.0_130618

Safety information

Keep signs legible

Keep any signs affixed to the device in an easily readable condition:

Connection labels

Warning and information signs

Motor data and rating plates

2.5 Motor protection

The pump motor has a temperature sensor on the circuit board as

overload protection. In the event of excessive temperature or if the

motor is blocked, the vacuum pump switches off.

If the vacuum pump is switched off due to these safe‑

ty precautions, the error must be cleared manually:

Unplug vacuum pump from power supply ‑> eliminate cause of

error ‑> switch vacuum pump back on.

Labels and signs

Procedure for

switching vacuum

pump back on

Overheating

protection, blockage

protection

Summary of Contents for MV 10C VARIO select

























































































Search results

Summary of Contents for MV 10C VARIO select

Reviews:

Related manuals for MV 10C VARIO select

Brands by name

Popular brands

vacuubrand MV 10C VARIO select, Instructions For Use Manual

Search results

Summary of Contents for MV 10C VARIO select

Reviews:

Related manuals for MV 10C VARIO select

Brands by name

Popular brands