2GN/2GP/2GR
1-4-38
C8210
Stapler moving motor 1 error
(optional 3000-sheet document fin-
isher)
When operation returned to a home
position is performed at the time of initial
operation and a home position is not
detected even if 1.5 s passed.
Poor contact in the
connector termi-
nals.
Check the connection of connector YC9 on
the finisher main PWB and the connector of
stapler moving motor 1, and the continuity
across the connector terminals. Repair or
replace if necessary.
Defective stapler
moving motor 1.
Replace stapler moving motor 1.
Defective finisher
main PWB.
Replace the finisher main PWB and check
for correct operation.
Stapler problem (optional document
finisher)
When the stapler motor is driving, the
ON status of the stapler home position
sensor cannot be detected even if a
specified time has elapsed.
The stapler con-
nector makes poor
contact.
Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
remedy or replace the cable.
The stapler is
blocked with a sta-
ple.
Remove the stapler cartridge, and check the
cartridge and the stapling section of the sta-
pler.
The stapler is bro-
ken.
Replace the stapler and check for correct
operation.
Defective finisher
main PWB.
Replace the finisher main PWB and check
for correct operation.
Finisher stapler problem (optional
built-in finisher)
The stapler home position sensor does
not change state from nondetection to
detection within 200 ms of the start of
stapler motor counterclockwise (forward)
rotation.
During initialization, the stapler home
position sensor does not change state
from non-detection to detection within
600 ms of the start of stapler motor
clockwise (reverse) rotation.
The stapler con-
nector makes poor
contact.
Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
remedy or replace the cable.
The stapler is
blocked with a sta-
ple.
Remove the stapler cartridge, and check the
cartridge and the stapling section of the sta-
pler.
The stapler is bro-
ken.
Replace the front stapler and check for cor-
rect operation.
Defective finisher
control PWB.
Replace the finisher control PWB and check
for correct operation.
C8220
Stapler moving motor 2 error
(optional 3000-sheet document fin-
isher)
When operation returned to a home
position is performed at the time of initial
operation and a home position is not
detected even if 3.5 s passed.
Poor contact in the
connector termi-
nals.
Check the connection of connector YC10 on
the finisher main PWB and the connector of
stapler moving motor 2, and the continuity
across the connector terminals. Repair or
replace if necessary.
Defective stapler
moving motor 2.
Replace stapler moving motor 2.
Defective finisher
main PWB.
Replace the finisher main PWB and check
for correct operation.
C8230
Stapler motor problem (optional 3000-
sheet document finisher)
Jam 82 is indicated.
Poor contact in the
connector termi-
nals.
Check the connection of connector YC10 on
the finisher main PWB and the connector of
stapler motor, and the continuity across the
connector terminals. Repair or replace if
necessary.
Defective stapler
motor.
Replace the stapler motor.
Defective finisher
main PWB.
Replace the finisher main PWB and check
for correct operation.
Code
Contents
Remarks
Causes
Check procedures/corrective measures
Summary of Contents for CD 1230
