Utax CD 1218 Instruction Handbook Manual Download Page 95

Page: 95 / 114

Troubleshooting

6-14

If the optional duplex unit is installed, raise the duplex
unit and remove any paper.

Note

If the paper does happen to tear, remove any loose scraps from inside the machine.

Close the left cover.

Paper Jam in the Paper Output Slot

Paper

misfeed in Eject section Remove

paper

appears and the jam location indicator shown in

the illustration blinks, a paper jam has occurred in the
paper output slot. Perform the following procedure to
remove the jammed paper.

Important!

The drum section inside the main body is sensitive to scratches and contaminants. When removing
paper, be careful not to touch it or scratch it with your watch, ring, etc.

If jammed paper is seen through the paper output slot,
pull it out to remove it.

Note

If the paper does happen to tear, remove any loose scraps from inside the machine.

Pull the left cover handle up to open the left cover.

Paper misfeed in

Eject section

JAM50

Remove paper.

Summary of Contents for CD 1218



















































































































Search results

Summary of Contents for CD 1218

Reviews:

Brands by name

Popular brands

Utax CD 1218, Instruction Handbook Manual

Search results

Summary of Contents for CD 1218

Reviews:

Brands by name

Popular brands