Utax CD 1218 Instruction Handbook Manual Download Page 49

Page: 49 / 114

Basic Operation

3-8

Set the original.

Press the

Duplex

key.

Press the

key or the

key to select the desired

duplex copy mode.

Press the

Enter

key.

If you have selected

1 sided->2 sided

, proceed to the next step.

If you have selected

2 sided->2 sided

Book->2-sided

, proceed to step 7.

Press the

key or the

key to select the desired

finished stitch side.

Press the

Enter

key.

Press the

Start

key. Scanning of the original starts.

If the originals have been set in the optional document processor, copying starts automatically.

If the original has been set on the platen, a message prompting replacement of the original is
displayed. In this case, proceed to the next step.

Replace the original and press the

Start

key. Scanning of the original starts.

If no original remains, press the

Enter

key. Copying starts.

Book

1 sided

2 sided

2-sided

Duplex/Split Page:

Saddle Stitch Direction:

Left side

Top side

Summary of Contents for CD 1218



















































































































Search results

Summary of Contents for CD 1218

Reviews:

Brands by name

Popular brands

Utax CD 1218, Instruction Handbook Manual

Search results

Summary of Contents for CD 1218

Reviews:

Brands by name

Popular brands