background image

Operating Manual

www.ushio.com

13

4.  Care and Maintenance 

UDC PSC Unit Cleaning

The 

UDC PSC

 unit is rated for water resistance. The 

UDC PSC

 unit is rated for slight water 

contact and mild detergent cleaning solutions only. However, it should NOT BE IMMERSED 

in water or cleaning solutions for any prolonged periods of time. After cleaning, remove 

UDC 

PSC

 unit from cleaning solution, dry and store the device in a clean and dry environment.

WARNING!

Failure to comply with the following may result in damage to the 

UDC PSC

 

unit and will void the product warranty.

Use caution when cleaning the 

UDC PSC

 unit; some methods may be harmful and could 

result in extensive damage. Manual cleaning is the recommended method. Certain cleaning 

agents may damage the device’s materials. Only use water with a mild detergent such as a 

nonabrasive hand or dishwashing soap. Do not immerse the 

UDC PSC

 unit in an ultrasonic 

cleaner.

CAUTION!

Ensure that the battery hatch door is fully tightened on the O-ring seal to 

prevent liquid intrusion into the battery compartment.

Never use any organic solvents to clean the 

UDC PSC

 unit, other than  

isopropyl alcohol.

Drying the UDC PSC Unit

If the 

UDC PSC

 unit comes in contact with liquid, rinse with isopropyl alcohol and then dry 

with compressed air, commercial compressed gas canisters or dry damp cloth.

Note: Air dry is highly recommended to reduce contamination of the optical 

components and reduce the possibility of oxidation of the materials used in the 

construction of the 

UDC PSC

 unit.

CAUTION!

Do not allow the 

UDC PSC

 unit to remain in liquid cleaning solution for 

prolonged period of time.

In addition, thoroughly dry the battery hatch door seal around the O-ring, with compressed 

air or by thoroughly wiping any excess liquid from this area, prior to removing the battery 

hatch door. This will prevent any trapped fluid from entering the battery compartment and 

exposing the electronics to fluids.

CAUTION!

Ensure there is no trapped liquid between the battery hatch door and body 

prior to removing the battery hatch door.

Summary of Contents for 9500037

















Reviews: