US Robotics USR5454 User Manual Download Page 116

Page: 116 / 130

file:///G|/CSO/Documentation/Documentation%20-%20Draft/Networking/5454%20Mach-1%20AP/User%20Guide/English/regulatory.html

For Canadian Users

Industry Canada (IC)

This equipment complies with RSS-210 of the Industry Canada Rules.

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause

undesired operation of the device.

To prevent radio interference to the licensed service, this device is intended to be

operated indoors and away from windows to provide maximum shielding.

Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

This device has been designed to operate with an antenna having a maximum gain of 2

dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry

Canada. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the Equivalent Isotropic Radiated Power (EIRP) is not more

than that required for successful communication.

file:///G|/CSO/Documentation/Documentation%20-%20Dr...%20Mach-1%20AP/User%20Guide/English/regulatory.html (4 of 9)10/26/2006 9:47:17 AM

Summary of Contents for USR5454



































































































































Search results

Summary of Contents for USR5454

Reviews:

Brands by name

Popular brands

US Robotics USR5454, User Manual

Search results

Summary of Contents for USR5454

Reviews:

Brands by name

Popular brands