US Robotics USR5454 User Manual Download Page 111

Page: 111 / 130

file:///G|/CSO/Documentation/Documentation%20-%20Draft/Networking/5454%20Mach-1%20AP/User%20Guide/English/faq.html

Wireless Nd1 Access Point:

User Guide

●

Home

●

Installation

●

Configuration

●

Tutorials

●

Help

Frequently Asked Questions

Can I use SecureEasySetup to configure wireless security for the access point?

Yes. For the initial setup of the access point, refer to the

installation

instructions

1. Click the

SecureEasySetup

button on the back of the access point.

2. Press the

SecureEasySetup

button in the utility for the client

adapter. Your client adapter will display a message when the

connection has been successfully completed.

How do I restore the access point to its factory default settings?

First, be aware that restoring the factory default settings loses all

configuration changes that you made.

file:///G|/CSO/Documentation/Documentation%20-%20Dr...ng/5454%20Mach-1%20AP/User%20Guide/English/faq.html (1 of 2)10/26/2006 9:47:17 AM

Summary of Contents for USR5454



































































































































Search results

Summary of Contents for USR5454

Reviews:

Brands by name

Popular brands

US Robotics USR5454, User Manual

Search results

Summary of Contents for USR5454

Reviews:

Brands by name

Popular brands