826
MULTI-PURPOSE ELECTRIC LOCK TIMER
Ref. 1032/81
FEATURES
Timer 1032/81 is used to control electric locks in SCAIBUS system
installations or second-generation Model 826 Digital Call System
installations. It is interfaced with the corresponding entrance module in
order to control the following types of electric lock:
•
Direct activation via capacitive discharge.
•
Activation via capacitive discharge and 150 mA holding current.
•
Electric security locks.
DIAGNOSTICS LED
The timer is provided with a LED to diagnostics during installation, two
jumpers used for timer confi guration, and a trimmer used to set relay
output actuation time.
LED LI: On when input SE2 is active.
LED LO: On when relay output is active.
JUMPERS AND CONFIGURATIONS
AR:
Recycle enabling.
AMCR: Relay common ground enabling.
TIME: Output relay de-energizing delay trimmer. For maximum delay,
turn trimmer clockwise.
Note:
When operating with jumper AR in “NO” position, the timer will
activate relay output upon receiving a command via input “SE2”
only for the time set by means of the trimmer, regardless of
whether or not the input signal persists.
When operating with jumper AR in “YES” position, the timer
will activate relay output at least for the time set by means of
the trimmer: if input “SE2” signal persists beyond this time, the
output will continue to remain active.
TERMINAL DESIGNATIONS
+24 :
Power supply input, 22 to 27 V DC
+12/~: Power supply input, 10 to 15 V DC or 10 to 15 V AC
-/~ :
Power supply common
-/ ~:
Power supply common
SE2 : Timer control input;
power supply common
AP :
Door lock release output
NO :
Normally open contact
NC :
Normally closed contact
C :
Common to both contacts; normally connected to power supply
common
SPECIFICATIONS
Power supply voltage at +24:
22 to 27 V DC
Power supply voltage at +12/~:
10 to 15 V DC/AC
Direct current output from AP:
125 to 170 mA
Consumption in load units (LU):
20 LU
Timer range:
1 to 30 sec ± 20%
Service temperature range:
-10 to 45°C
Maximum resistive load switching capacity:
10 A with 24 V DC / 10 A with 120 V AC
Maximum switching voltage:
40 V AC / 110 V DC
Maximum resistive switching capacity:
1400 VA with 240 V AC / 300 W with 110 V DC
Minimum applicable load:
10 mA with 5 V DC
Maximum current draw at 12 V DC:
200 mA
Dimensions
Length:
72 mm (four 18 mm modules)
Width:
90 mm
Height:
75 mm
INSTALLATION
The timer can be installed on a DIN rail, or can be wall mounted using
screws and wall plugs (not provided with the unit).
MULTI-PURPOSE ELECTRIC LOCK TIMER Ref. 1032/81
MULTI-PURPOSE ELECTRIC LOCK TIMER
Ref. 103
2
/8
1
E
Q
UIPME
N
T
F
OR SPECI
A
L SER
V
ICES
A
ND
F
U
N
CTIO
N
S
AP
LO
TIME
AMCR
C
NC NO
AR
SI
+24
=12/~
−
/~
−
/~
SE2
1
30 sec
NO
1
- 68
MT124-019
Summary of Contents for 826 DIGITAL CALL SYSTEM
