urmet domus 826 DIGITAL CALL SYSTEM, Manual

Page: 37 / 118

826
The display will show the:
First door lock release code (“0000”): change or confi rm.
Press
.
The second door lock release code “0000” will then appear:
change or confi rm.
Press
.
The third door lock release code “0000” will appear:
change or confi rm.
Press
.
“
“
“
The eighth door lock release code “0000” will appear:
change or confi rm.
Press
.
The entrance module will store the codes in memory and return to
normal operation.
It is recommended that only one person in the building (i.e., the
building manager or concierge) know the password, and that all
door lock release code programming operations be carried out
only by this person.
NOTE: Though door lock release codes cannot be transmitted over
the data line, they are in all other respects identical to special
service codes. If special services decoders are installed in the
system, they must thus be programmed with codes differing
from all door lock release codes.
BUSY SIGNAL VOLUME ADJUSTMENT
The entrance module generates a busy signal when a call is in
progress from another entrance module or guard door switchboard
station. Volume of this signal can be adjusted by means of trimmer
(11) located at the rear of the entrance module.
SPEAKER AND MICROPHONE VOLUME ADJUSTMENT
FOR SPEAKER UNIT Ref. 5150/500 or Ref. 824/500
See instructions enclosed with speaker unit.
NOTICE: The speaker unit is intended for use with electronic
call tone signaling doorphones and monitors. If conventional
buzzer type apartment station equipment is used, disassemble
the speaker unit, disconnect the brown wire from terminal 1A and
connect it to terminal 1.
REPLACING AN OLD ENTRANCE MODEL WITH A
SECOND-GENERATION MODULE
•
STEP 1:
−
Enter 0 if confi gured as main entrance panel.
−
Enter 1 if confi gured as secondary entrance panel.
•
STEP 2:
−
Enter 1.
•
STEP 3:
−
Enter 000 if confi gured as main entrance panel
−
Enter 1 if confi gured as secondary entrance panel
No. 1.
−
Enter 2 if confi gured as secondary entrance panel
No. 2.
−
Enter 9 if confi gured as secondary entrance panel
No. 9.
•
STEP 4: See instructions.
•
STEP 5: See instructions.
•
STEP 6: See instructions.
First-generation systems can operate only with conventional type
apartment station equipment. Consequently, the speaker unit
must be disassembled and the brown wire disconnected from
terminal 1A and connected to terminal 1.
ENTRANCE MODULE ON KOMBI CHASSIS Ref. 826/65
OPERATION
OPERATION
The number entered on the entrance module keypad is shown on the
display. An acoustic signal is generated each time a key is depressed.
When the call button is pressed, the ringer at the called apartment
station will be activated for the entire period that the call button is held
down. A protection feature will interrupt ringing if the call button is held
down for more than 5 seconds.
If an error is made when entering the code, pressing the delete button
“X” will cancel the number shown on the display.
Call codes can consist of a maximum of four digits, and may not begin
with zero. They are always shown on the display.
In addition, special codes are used for electric door lock actuation or
for other special services. These codes begin with zero and are not
shown on the display. After the zero is entered, the display will thus
show a line of dashes instead of the other digits: “————” . As for call
codes, special codes must be followed by pressing the
button.
ENT
R
A
N
C
E
M
O
DUL
E ON
K
O
MBI
CH
ASSIS
Ref.
826
/6
5
O
U
T
D
OO
R
S
T
A
T
ION E
Q
UI
P
M
ENT
1
- 29
MT124-019