urmet domus 826 DIGITAL CALL SYSTEM, Manual

Page: 53 / 118

826
CONFIGURATION
To operate correctly, the digital guard door switchboard station must
be appropriately confi gured at the time of installation. Confi guration
programming consists of assigning numeric parameters to all operating
variables.
When it leaves the factory after inspection, the switchboard station is
confi gured as follows:
Step Default confi guration
1 0
2 1 (2 nd generation, installation type 1)
3 0 (Main)
4 0 (Serial line disabled)
4a - CONFIGURATION NOT REQUIRED
5 1 (Electronic call tone signaling doorphone)
6 0 (Concierge service enabled)
6a - CONFIGURATION NOT REQUIRED
7 0 (Key A disabled)
7a - CONFIGURATION NOT REQUIRED
8 0 (Key B disabled)
8a - CONFIGURATION NOT REQUIRED
9 0 (Key C disabled)
9a - CONFIGURATION NOT REQUIRED
10 0 (Key D disabled)
To change one or more confi guration parameters, activate the
confi guration cycle bearing the following points in mind:
•
Parameters must be entered only by means of the number keys.
•
After selecting each parameter (with the exception of language in
Step 1), press the call button (8) to confi rm selection.
•
The system will check all entered data, rejecting any data which are
not congruent.
•
Any errors made in entering parameters can be corrected with the
delete key (9) before confi rming entries.
The default confi guration will return to the display.
•
To return to the beginning of the programming procedure at any
time, press scroll key (5)
•
Write down the parameters confi gured during each programming
step on the label provided for this purpose. Label is located under
the name card in the directory drawer (13).
It is strongly recommended that confi guration data be recorded
on the label, as it may be needed at a later date if the data memory
must be replaced as a result of malfunction or for servicing.
To activate the confi guration cycle:
•
Supply power to the switchboard station, hold down the DAY/NIGHT
button (18) and press the call button (8) twice in succession within
3 seconds.
At the end of this operation, the fi rst menu will appear on the display.
This menu is used to select operating language.
STEP 1 - Language
With the confi guration cycle active, the following message will appear
on the switchboard station display:
•
Press the number key associated with the desired language as
indicated on the display
STEP 2 - Installation type
The display will show:
Perform one of the following operations:
•
Press number key “0” if the switchboard station is to be installed in
a fi rst-generation system.
•
If the switchboard station is to be installed in a second-generation
system, press number key “1” to select installation type 1 (up to 9
riser cables serving 999 apartment stations each), number key “2”
to select type 2 (up to 89 riser cables serving 99 apartment stations
each), or number key “3” for type 3 (up to 899 riser cables serving
9 apartment stations each).
After selecting installation type, or if the default confi guration is correct
for the system in question, press the call button (8) to go on to the next
confi guration step.
STEP 3 - Main/secondary switchboard station
The display will show:
Select “0” in all cases. The option “1” can only be used in special
applications. Press the call button (8) to go on to the next confi guration
step.
STEP 4 - RS 232-C serial line enabling
The display will show:
The digital switchboard station is equipped with an asynchronous RS
232-C interface with the following characteristics:
Data format
Start bit : 1
Word : 8 bits
Parity bit : None
Stop bit : 1
Speed
2400 bit/sec
Connector (26)
9-pin male D connector
To enable serial communication with a printer or personal computer,
select “ON” by pressing number key “1” followed by the call button (8).
5 8
18
9
ITALIA = 0 FRANC = 1
ENGL = 2
DEUTSCH = 3
PROGRAMMING
TYPE: 1
0 = MAIN
1 = SECONDARY
: 0
SERIAL LINE
0 = OFF, 1 =ON :0
DIGITAL GUARD DOOR SWITCHBOARD STATION Ref. 826/18
CONFIGURATION
D
IGITA
L
GUAR
D D
OOR
S
W
ITC
H
B
OAR
D S
TATION
R
ef
.
826
/1
8
GUAR
D D
OOR
S
TATION
E
Q
UI
P
M
E
NT
1
- 45
MT124-019