29
To rinse thoroughly, press the button „Coffee mug“ three times.
Pour this coffee away.
In order to save coffee, adjust the selector switch above the brewer
assembly to minimum.
If necessary, the automatic descaling process can be started
after the manual descaling, in order to descale the appliance
completely.
aUtoMatIc DescalING
The automatic descaling memory is permanently activated. In
the menu you may choose the intervals of 500/1000/1500 and
2000 cups. After obtaining the set number of cups, the appliance
switches to AUTOMATIC DESCALING mode. The automatic
descaling programme can be initialised manually at any time.
atteNtIoN:
Never turn the steam control to aUs [oFF/o] when descaling the
appliance, if not explicitly required by means of the displayed
messages. otherwise the descaling time already passed will be
deleted and the programme will start a new descaling process.
as the descaling programme requires several steps, you should stay
near the appliance in order to carry out the steps the programme
needs to continue.
Use an ecological descaling product. Make sure that the descaling
product is adequate for automatic coffee machines.
The service life of the appliance is considerably prolonged if you
fill the tank with water treated with a commercial softening agent
(filter cartridges).
If the automatic coffee machine indicates
GERäT
ENTKALKEN
(DESCALE APPLIANCE), the appliance has to be descaled.
Place a jug under the frother with a capacity high enough for the
discharged water.
Fill the water tank with fresh water and add the corresponding
amount of descaling product, following the instructions of the
manufacturer.
Turn the steam control to
eIN
[ON]. The following message is
displayed:
ENTKALKEN
STARTEN
The automatic descaling programme will be initialised. The
duration is of about 30 minutes.
When the display indicates
SPÜLVORGANG
LäUFT
(RINSE IN PROGRESS), turn the steam control to
aUs
[OFF].
Detach the water tank and fill it with fresh, cold water. Insert the
water tank and continue the descaling process.
Turn the steam control to
eIN
[ON]. Possible residues are
eliminated when rinsing. After this process finishes, the display
indicates the following:
DAMPFREGLER
AUS
Turn the steam control to
aUs
[OFF]. The following message will
be displayed:
ENTKALKEN
BEENDET
This messages remains on the display for 5 seconds.
The appliance starts to heat up and the display indicates
AUFWäRMEN
(HEATING UP), until the necessary operation temperature to brew
coffee is achieved and the display newly indicates the following:
BETRIEBSBEREIT
The descaling programme is finished and the appliance is ready
for operation again.
trouble shooting
When the display indicates
WASSERTANK
FÜLLEN
(FILL WATER TANK), the water tank is empty. Detach the water
tank, fill it with cold water and reinsert it into the appliance to re-
establish the operating state. If the float lever is blocked, gently
shake the water tank to set it free. If the water tank is full and
the message is displayed all the same, please lift the water tank
briefly and reinsert it.
When the display indicates
BRÜHGRUPPE
EINSETZEN
(INSERT BREWER ASSEMBLy), the brewer assembly is not
properly inserted. Open the lateral cover and detach the coffee
grounds container first, then the brewer assembly. The brewer
has two arrow marks on the front beneath the handle. These must
point at one another to allow the insertion of the brewer assembly.
Should this be not the case, the brewer assembly may be aligned
with the brewer assembly key/wrench. Insert the brewer assembly
key/wrench into the hole on the rear of the brewer assembly and
turn it until the arrows on the front point at one another.
When inserting the brewer assembly, the plate with the label
PRESS above the handle has to be pushed down. The brewer
assembly must latch into place.
When the display indicates
SATZBEHäLTER
LEEREN
(EMPTy GROUNDS CONTAINER), the coffee ground container
is full and has to be emptied. Open the lateral cover and remove
the coffee grounds container. Empty the container and rinse it
thoroughly with water. Dry the container and reinsert it into the
appliance. Close the lateral cover.
The following message will be displayed:
STANDBy
Pressing the right button, the appliance will be ready for operation
again.
When the display indicates
SATZBEHäLTER
EINSETZEN
Summary of Contents for 28811
Page 6: ...6 Einzelteile 1 2 3 4 6 7 8 9 10 11 12 5 15 14 13 16 ...
Page 95: ...95 Notizen ...
Page 100: ...Aus dem Hause ...
