Unitek BAMOCAR-D3-700-100 Manual Download

Page: 5 / 51

Basic information

BAMOCAR-D3-700-100/160

Version: 2019 / V05

Valid

ity

2.4

Validity

Hardware state:

TMS 2-3d, mBAMOCAR1-1

Firmware state:

as from FW 476

2.5

Designations and symbols

Unit:

BAMOCAR-D3-700-100/160

User:

Vehicles, boats, manufacturers or operators of machines or installations in

the industrial sector (B2B, secondary environment).

Manufacturer:

UNITEK Industrie Elektronik GmbH

Dealer:

Caution – Danger to life!

High voltage!

Warning!

Important!

Dangerous electric fields!

Scope of delivery/included in the packaging:

BAMOCAR-D3-700-100/160

documentation

CD UNITEK DOKU-SOFT

Not included/Cannot be ordered from UNITEK:

Accessory connectors and cable glands.

35-pin connector type: Typo 776164-1

14-pin connector type: Typo 776273-1

Cable gland:

M25x1.5

Summary of Contents for BAMOCAR-D3-700-100




















































Search results

Summary of Contents for BAMOCAR-D3-700-100

Reviews:

Related manuals for BAMOCAR-D3-700-100

Brands by name

Popular brands

Unitek BAMOCAR-D3-700-100, Manual

Search results

Summary of Contents for BAMOCAR-D3-700-100

Reviews:

Related manuals for BAMOCAR-D3-700-100

Brands by name

Popular brands