Unitech MS842N User Manual Download Page 29

Page: 29 / 132

Enter Setup

Chapter 4 Scanning Preferences

Introduction

This chapter contains information as to how to adapt your engine to various applications with preference setting. For

instance, to improve barcode reading performance off mobile phones and LCD displays; or to narrow the field of view of the

engine to make sure it reads only those barcodes intended by the user.

Regular Mode/Mobile Phone Mode

The engine can capture barcodes printed on paper labels or displayed on the screen of a mobile phone. Select a mode as

per actual need.

Regular Mode:

Read barcodes printed on paper or plastic.

Mobile Phone Mode:

Read barcodes off mobile phones or LCD displays.

Regular Mode

Mobile Phone Mode

Decode Area

Whole Area Decoding

When this option is enabled, the engine attempts to decode barcode(s) within its field of view, from the center to the

periphery, and transmits the barcode that has been first decoded.

** Whole Area Decoding

Exit Setup

Summary of Contents for MS842N





































































































































Search results

Summary of Contents for MS842N

Reviews:

Related manuals for MS842N

Brands by name

Popular brands

Unitech MS842N, User Manual

Search results

Summary of Contents for MS842N

Reviews:

Related manuals for MS842N

Brands by name

Popular brands