Unitech MS842N User Manual Download Page 109

Page: 109 / 132

Extend to UPC-A

Disabled

System Character “0”

Do not transmit

UPC-A

UPC-A Enabled

Check Digit

Transmit

2-Digit Add-On Code

Disabled

5-Digit Add-On Code

Disabled

Preamble Character “0”

Do not transmit

Interleaved 2 of 5

Interleaved 2 of 5

Enabled

Parity Check

No Parity Check

Check Digit

Do not transmit

Maximum Length

Minimum Length

Minimum length supported: 4

Discrete Length

Disabled

ITF-6

ITF-6 Disabled

ITF-14

ITF-14 Disabled

Code 39

Code 39

Enabled

Parity Check

Disabled

Start/Stop Character

Transmit

Code 39 Full ASCII

Disabled

Maximum Length

Minimum Length

Minimum length supported: 4

(including start/stop characters

and check digit)

Codabar

Codebar Enabled

Parity Check

Disabled

ABCD/ABCD format

Uppercase

Transmit

Start/Stop Character

Maximum Length

Summary of Contents for MS842N





































































































































Search results

Summary of Contents for MS842N

Reviews:

Related manuals for MS842N

Brands by name

Popular brands

Unitech MS842N, User Manual

Search results

Summary of Contents for MS842N

Reviews:

Related manuals for MS842N

Brands by name

Popular brands