Unitech MS282 User Manual Download Page 146 | Manualshive

Page: 146 / 169

background image

- 129 -

© 2018 unitech Electronics Co., Ltd. All rights reserved.

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS282 User’s Manual

3.21 Lock/Unlock Parameter Scanning

This feature locks parameter settings with a 4-digit code to prevent the user
from changing parameter values by scanning parameter bar codes. This
provides an added level of security not offered via Disable Parameter
Scanning.

To lock parameter scanning:
1.Scan the Lock bar code.
2.Scan four bar codes from

Appendix B, Numeric Bar Codes

that represent the

desired code. Enter leading zeros for numbers below 1000, e.g., to program
a code of 29, enter 0, 0, 2, 9. A "lock" beep sounds (two long high beeps) in
addition to the parameter entry beep.

To unlock parameter scanning:
1.Scan the Unlock bar code.
2.Scan four bar codes from

Appendix B, Numeric Bar Codes

that represent the

correct code. An "unlock" beep sounds (two long low beeps) in addition to
the parameter entry beep.

Entering an incorrect code results in a parameter error beep.

Lock

Unlock

«
...
144
145
146
147
148
...
»

Summary of Contents for MS282










































































































































































Reviews:

No comments

Related manuals for MS282

Brand: Leuze Pages: 92

Brand: Hand Held Products Pages: 56

Brand: Nedap Pages: 5

Brand: Hama Pages: 6

Brand: Iseo Pages: 2

TN-UHF LNX Series

Brand: turck Pages: 85

Brand: Speedata Pages: 10

Brand: ViewSonic Pages: 2

Brand: AuthenTrend Pages: 33

Brand: Di-soric Pages: 174

Brand: IdAutomation Pages: 89

Brand: ealloora Pages: 28

Brand: Datalogic Pages: 117

Brand: Unitech Pages: 2

Brand: Datalogic Pages: 169

Brand: Omron Pages: 236

Brand: FEITIAN Pages: 14

Brand: Obreey Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands