Unitech MS282 User Manual Download Page 129

Page: 129 / 169

- 112 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS282 User’s Manual

3.16.3 Composite TLC-39

Scan one of the following bar codes to enable or disable Composite bar
codes of type TLC-39.

3.16.4 Composite Inverse

Select an option to set Composite for either regular decode or inverse
decode.
•

Regular Only

- The engine decodes regular Composite bar codes only.

Before selecting this, set Inverse 1D to Regular Only or
Inverse Autodetect.

•

Inverse Only

- The engine decodes inverse Composite bar codes only.

This mode only supports Composite Inverse that includes
DataBar combined with CCAB, and does not support
other 1D/2D combinations. Before selecting this, first
enable Composite CC-A/B , and set Inverse 1D to Inverse
Only or Inverse Autodetect.

Enable TLC39

Disable TLC39*

Regular Only*

Inverse Only

Summary of Contents for MS282


























































































































































Search results

Summary of Contents for MS282

Reviews:

Related manuals for MS282

Brands by name

Popular brands

Unitech MS282, User Manual

Search results

Summary of Contents for MS282

Reviews:

Related manuals for MS282

Brands by name

Popular brands