ENGLISH
ENGLISH
10
11
2. Do not touch the hot Lid immediately after cooking to avoid scald.
•
For safety never cover the Lid edge with towel.
•
Never attempt to open the Lid by force if there is pressure inside. It is dangerous.
•
After cooking before opening the Lid first cut the power.
KEEP THIS INSTRUCTION MANUAL!
BEFORE USE
•
Remove the packing materials from the inside and outside of the appliance and from the acces-
sories.
•
Place the device on a flat dry surface.
•
Wash all the parts, which may contact with the food including the Inner pot, the Measuring Cup,
the Ladle and the Steamer in warm soap water, rinse and dry.
•
Wipe inside and outside of the appliance, and the Lid with the wet sponge and than with a clean
dry cloth.
•
Before connecting the cooker to the supply, check the applicable voltage indicated on the appli-
ance to see whether it corresponds to that of the main supply (220-240 V, 50-60 Hz).
•
Don’t dip the appliance into water or other liquid!
STEAMER FUNCTION
The appliance can be used as a Steamer. For this purpose use a special accessory that you have
bought with the appliance – the Steamer.
•
Add some water (1/6 scale) into the Inner Pot. Put the Steamer with kitchen-stuff into the Inner
Pot and close the Lid.
•
Turn the Relief Valve to “Герметично” position.
•
Power on the appliance with the Power Cord.
•
Choose the button “Пароварка”.
•
Cooking time is up to your preferences – control the cooking time according to your food or
menu. For this use the “Установка времени” button.
•
Press the button if you would like to stop the cooking process.
CLEANING
•
Remove the plug from the socket before cleaning wait until the appliance has normal temperature.
•
Take out the Inner Pot or Bowl for Smoking and clean it with a sponge or nonmetal soft brush,
and then dry it with towel.
•
Rub the Inner Surface of the appliance with a soft cloth.
•
Clean the outer coating of the appliance with a soft slightly wet towel. Never dip it in water for
cleaning or run water over it.
•
Take off the Water Collector and clean it with a wet towel. Put it back as shown in the picture:
•
Clean the Sealing Gasket, Relief Valve, and Floating Valve with soap water then dry them with a
towel. After cleaning put the parts together again.
Attention!
For your safety remember that when the appliance is on it must not contact with water or
other liquids especially the cord and the base of the appliance.
You must not dip the appliance into the water to avoid electric shock, fire or injuring.
Never wash the appliance in a dishwasher!
TROUBLESHOOTING
SPECIFICATIONS
Model
Rated Volt-
age
Power
Capacity
Diameter
Working
Pressure
USP-1210S
220-240V
1100 W
6L
22 cm
0-70 kPa
Max Pres-
sure
Keeping
warm Tem-
perature
Pre-set Time
Pressure-
keeping
Time
Max keep
warm Time
Lifetime
90 kPa
70-80°C
0-24 hours
1-60 min
0-24 hours
20000 cycles
but not more
than 5 years
from the
date of the
purchase
The head office of the manufacturer :
«UNIT Handelsgesellschaft G.m.b.H.»
131, Gersthofer Str., A-1180, Vienna, Austria
Exported by:
«UNIT Electronics (H. K.) Limited»
3905 Two Exchange Square, 8 Connaught
Place,
Central,
Hong
Kong
The Manufacturer’s representative in Russia:
Unit Production Ltd, 109147, 34/10,
Marksistskaya
str.,
Moscow,
Russia,
tel. +7 (495) 748 09 17, email: www.unit.ru
Made in People’s Republic of China (P.R.C.)
This appliance is to be stored and used under the following conditions: temperature
– not less than +5°C; relative humidity - not higher than 80%; aggressive impurities in
the air: not allowable.
As the Manufacturer is constantly working on the improvement of its products, the
design and technical specifications are subject to change without prior notice.
www.unit.ru
NO.
A Problem
The Cause
The Solution
1
Difficult to close the
Lid
The sealing gasket is not fixed
well
Fix the sealing gasket well
2
Difficult to open the
Lid
The pressure inside is too high
Let the steam out turning the
relief valve left or right
3
Steam leaks off the
Lid
There isn't a sealing gasket in
the Lid
Put the sealing gasket into
the Lid (see “Appliance use”
paragraph)
The sealing gasket isn't clean
Clean the Sealing Gasket
The sealing gasket is damaged or
deformed
Change a broken or de-
formed Sealing Gasket to a
new one in a UNIT service
center
The Lid isn't fixed properly
Fix the Lid properly
4
Indicating lights are
not on
The appliance isn't powered on
Check the power cord and
the plug
Some other problems
Send the appliance to a UNIT
service center
5
E1
Open circuit of the sensor
Send the appliance to a UNIT
service center
E2
Short circuit of the sensor
E3
Over-temperature
E4
Disable signal switch
