background image

Unicont SPb Ltd 

 

Technical Documentation CH-105 

 

Page 17 

14.

 

Transportation and Storage 

The battery charger shall be stored in heated space at air temperature of +5 º

С 

to +35 º

С 

(maximum  values  of  -30 º

С 

to  +70 º

С

),  at  relative  humidity  of  air  not  exceeding  95 %  at 

temperature of +25 °C and content of dust, oil, moisture and aggressive admixtures in the air not 
exceeding the norms envisaged by GOST 12.1.005-88 for the working zone of production areas. 

The  device  shall  be  transported  in  transport  container  of  the  manufacturer  in  closed 

transport. 

Means of transport: 

 

automobile and railway closed transport (covered wagons, universal containers) 

 

by air (in pressurized and heated bays of airplane) 

 

by sea (in dry service spaces). 

The device shall be transported in accordance with the transport regulations in force for 

the particular transport. 

During  handling  operations  and  transportations  strictly  observe  the  requirements  of 

handling marks on boxes and do not allow bumps and impacts which can affect preservation and 
serviceability of the device. 

Packed devices shall be reliably secured in vehicles. 

After storage in stores or transportation at temperature below  +10 º

С 

the devices shall 

be  unpacked  only  in  heated  spaces  after  keeping  them  unpacked  in  under  normal  climatic 
conditions for12 hours. 

 

 

Summary of Contents for CH-105




















Reviews: