background image

Unicont SPb Ltd 

 

Technical Documentation CH-105 

 

Page 18 

15.

 

Warranty 

The manufacturer guarantees the unit CH-105 complies with this manual provided that 

the operation, transportation and storage conditions are adhered to during the warranty period. 

The  unit’s  warranty  period  expires  24  months  from  the  date  of  its  shipping  from  the 

manufacturer’s storehouse. 

Within the warranty period, the owner is entitled for a free repair, or a replacement of a 

separate part, provided that the malfunction occurred through the manufacturer’s fault. 

Warranty repair is provided if the unit is submitted with the manufacturer’s label and a 

legible serial number available on it, as well as this operating manual. 

The manufacturer is not responsible and cannot guarantee the unit’s operation: 

1.  After the warranty period is over; 
2.  In  case  of  the  failure  to  observe  the  unit’s  operation,  transportation,  storage  and 

installation rules and conditions; 

3.  If the unit is in an unmarketable condition, or has a damaged body, and other causes 

beyond the manufacturer’s control; 

4.  If self-made electrical devices were used. 
5.  If  there  was  an  attempt  to  repair  the  unit  by  a  person  who  is  not  an  authorized 

representative of the manufacturer. 

If  the  owner  loses  this  operating  manual  or  the  manufacturer’s  label  with  a  serial 

number, the manufacturer shall not provide their copies, and the owner shall be divested of the 
right for a free repair during the warranty period. 

Upon the warranty expiry, the manufacturer shall facilitate the repair of the unit at the 

owner’s expense. 

Note: in case of warranty repair, the unit’s disassembling from the installation site and 

its delivery to the manufacturer’s service center are done at the owner’s expense. 

Visit  the  manufacturer’s  website 

www.unicont.com

  (section  “support/warranty”)  to 

find: 

 

forms to fill in claims, 

 

full warranty description; 

 

full description of the warranty service rendering procedure. 

 
 
 
The manufacturer service center’s address and contact details:

 

Unicont SPb, Ltd.

 

Bld. 26Е Kibalchich Str., Saint Petersburg, 192174, Russia

 

tel.: + 7 (812) 602 02 64

 

fax: +7 (812) 362 76 36

 

e-mail: 

[email protected]

 

Summary of Contents for CH-105




















Reviews: