background image

 

 

DIGITAL BATTERY CHARGER 12V 8A 

GCHARG/108 
Rated Voltage: AC 220-240V   Rated Current: 0.60 Amp 
Output: DC 12V 2Amp / 8Amp   
 

 

 
      

IMPORTANT SAFETY INSTRUCTIONS 

 
1.

 

This appliance is not intended for use by persons (including children) with reduced physical, 
sensory or mental capabilities, or lack of experience and knowledge, unless they have been 
given supervision or instruction concerning use of the appliance by a person responsible for 
their safety. Children should be supervised to ensure that they do not play with the appliance. 

2.

 

Working in vicinity of a lead-acid battery is dangerous.  batteries generate explosive gases 
during normal battery operation. For this reason,  it is of utmost important that each time 
before using your charger, you read this manual and follow the instruction exactly. 

3.

 

To reduce risk of battery explosion , follow these instructions and those published 

by the battery manufacturer and manufacturer of any equipment you intend to use 

in vicinity of battery. Review cautionary markings on these products and on 

engine 

4.

 

Use the charger in door only , do not expose it to rain. 

 

 

 

Summary of Contents for Mac Afric GCHARG/108









Reviews: