background image

15

ENGLISH

Installation Instructions

3

INSTALLATION INSTRUCTIONS

ATTENTION!

This boiler is intended solely for 

the use for which it was expressly 

designed. Any other use is to be 

considered improper and therefore 

dangerous.

This boiler heats water at a temper-

ature lower than the atmospheric 

pressure boiling temperature.

Before connecting the boiler, have pro

-

fessionally qualified personnel:

a) Thoroughly wash all the piping of 

the system to remove any residues 

or impurities which could jeopard-

ise proper operation of the boiler, 

even from a hygienic point of view. 

b) Check that boiler is set up to oper-

ate  with  the  available  type  of  fuel.

 

This can be seen written on the 

package and on the technical feature 

plate;

c) Check that the chimney/flue has an 

appropriate draught, without any 

bottlenecks, and that no exhausts 

from other appliances are inserted, 

unless the flue has been implement

-

ed to accommodate several utilities 

according to specific standards and 

regulations in force. Only after this 

check can the fitting between the 

boiler and chimney/flue be mounted;

ATTENTION!

If there is dust and/or if there are 

aggressive/corrosive vapours 

present in the installation room, 

the appliance must be protected 

suitably and must be able to 

operate independently from the air 

in the room.

ATTENTION! 

Only mount the appliance on a closed 

wall,  made  of  non-flammable  materi

-

al,  flat,  vertical  so  that  the  minimum 

distances required for installation and 

maintenance can be observed.

The boiler must be connected to a cen-

tral heating system and/or domestic hot 

water supply network compatible with its 

efficiency and output.

3.1  -  GENERAL wARNINGS

3.2 - INSTALLATION STANDARDS 

It  must  be  installed  by  a  professionally  qualified 

technician, 

who shall take the responsibility of 

observing all local and/or national laws published 

in the official journal, as well as the applicable 

technical standards.

3.3 - PREVENTIVE VERIFICATION 

AND VERIFICATION AND AD-

JUSTMENT OPERATIONS

NOTE!

Further details in the section 

‘‘Technical Information’’ on the boiler page of the 

www.unicalag.it website 

NOTE!

Further details in the section 

‘‘Technical Information’’ on the boiler page of 

the www.unicalag.it website 

NOTE!

For further details relating to the standards, rules 

and regulations for safe installation of the thermal 

unit, refer to the section "Technical Information" 

on the boiler page of the www.unicalag.it website

The boiler can be installed outdoors 

in a partially protected place or in 

any case a place where the boiler is 

not exposed to direct atmospheric 

agents.

Summary of Contents for CoR C24





















































Reviews: