background image

28

3.11 -  MEASUREMENT OF COMBUSTION EFFICIENCY DURING INSTALLATION

ATTENTION!

Function reserved for Authorised 

Assistance Centres only.

3.11.1- ACTIVATION OF THE CALIBRATION FUNCTION

1

ACTIVATION

By pressing the button (

D

) for 5 seconds, until 

SErvice appears, 

Do not press it for more than 

9’’ (par. 4.2) 

This function is not activated if there is 

a block or domestic hot water request .

It is pos-

sible to dispose of heat on the sanitary circuit by 

opening 1 or more hot water taps.

all the symbols on the display flash

2

MAXIMUM OUTPUT

By turning the knob (B) onto MAX, the boiler will 

operate at 

maximum output:

- 1 lluminated symbol    

When the high flame symbol is fixed on the display 

and there is an alternation between 

SP

 and flow 

temperature, the boiler operates at maximum 

power.

Make combustion efficiency

4

DISABLING

The “calibration” function stays active for 15 min

-

utes.

To disable the 

CALIBRATION

 function before the 

time elapses press the button 

(D)

 for 5 seconds 

until the ‘SERVICE’ symbol appears

and then release. Do not press for more than

9 seconds.

3

MINIMUM OUTPUT

By turning the knob (B) in position        , the boiler 

will operate at 

minimum output

:

- 1 lluminated symbol   

 

and there is an alternation between 

SP

 and flow 

temperature, the boiler operates at minimum 

power.

Make combustion efficiency

x 5’’

The user is NOT authorised to activate 

the function described below. 

MAX

M

IN

MAX

M

IN

Summary of Contents for CoR C24





















































Reviews: