background image

 

13

 

4.3 Shut down Operation 

Close shut off valve (A), open pump vent valve (B), then turn off power switch of 

the pump(see Fig 4). If stopping the pump by no opening pump vent valve, the oil will 

be filled inside the pump cylinder within several minutes. This may cause back flowing 

oil to the vacuum vessel. For next operation, restarting the pump will be difficult 

because of not so smooth rotation, thermal protector operating, motor firing by over 

loading. 

When stopping the pump operation by electric stoppage, close shut off valve (A) quickly 

and then open pump vent valve (B). 

 

 

Firing hazard. As the surface of the pump body is higher temperature(70 

~80°C) during operation, do not touch it until cooled down after 

stopping the pump. 

 
 

① After closing shut off valve (A) and opening pump vent valve (B), stop 

the pump. If this procedure is not performed, pump oil must be filled 

inside the pump. It may cause difficulty on restarting or damage the 

pump, also back flowing oil to the vacuum vessel. 

② If the shut off valve (A) is not closed for shut down operation, this 

may cause air leakage through inside the pump to the vacuum vessel. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for GC-25Sa










































Reviews: