background image

 

NT 208D GB1

 

 

 

2 / 20

 

PREAMBLE :

 

 

Thank you for choosing Ultraflux to make your flow measurement. 
 
We offer a full range of portable or fixed flowmeters backed by 30 years’ expertise and 
experience using Ultrasonic techniques: 
 

  UF  801-P  family,  high  features  portable  flow  meters,  with  integral  loggers, 

signal analysis functions and many options. 

 
   

 UF 8xx families of fixed flow meters, applications include 

L - Liquids, 
G - Gas,  
MC - Multichord applications for Liquid and Gas measurement, 
CO / RV - Open Channel and River Flow Measurements. 

 
   

 The MiniSonic family with:  

– Portable Metering 

600/2000 single-channel fixed flowmeters, 
600-2 and 2000-2 for dual-chord flow metering, 
600-B and 2000-B for dual-pipe flow measurement configurations,  
Speed (1 or 2) is for open channel flow velocity measurements. 

 
 
This  manual  is  specifically  concerned  with  an  element  from  the  family  and  has  been 
drafted to guide you in the stages of installation and commissioning. 
 
Other documents and tools are available on paper or in electronic format: 
 

 A training manual concerning ultrasound measurement, reference NT 122  

 

  A  guide  about  the  use  of  our  software  in  the Windows  environment  reference 

NT 204A GB1 

 

 The RS communication protocol with its addresses table NT 207A GB1 

 

 The PC software, specific to your application, Ref LS 600W _version *** ,  with 

its delivered interconnection cable to a PC. 

 
 
All our equipments work on the principle of ultrasonic transit time difference and can be 
associated with clamp-on or wetted probes depending on the application. 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Minisonic_600-2





















Reviews: