Ultraflex ND1-MM Installation Manual Download

Page: 5 / 40

ZTF SYSTEM

page 5

of 39

Installation manual

ULTRAFLEX

MANUAL USE AND SYMBOLS USED

STERN

BOW

STARBOARD

PORT

Outboard

Engine

Tiller arm

Throttle

Shift

Lever

The picture aside explains the meaning of some

nautical words included in this manual.

THE INSTALLATION AND MAINTENANCE MANUAL should be kept for regular reference by the owner of the boat

and transferred to any new owner with the boat.

It is necessary to read carefully the manual, before ANY ACTIVITY involving the product, handling and unloading

included.

In this manual the following symbols are used to ensure the user safety and to guarantee the correct operation

of the product:

Immediate hazards which CAUSE severe personal injury or death.

The symbol aside indicates all the operations which must be carried out by

qualified or skilled staff, in order to avoid hazards.

We recommend training the staff in charge of the product installation and

checking their knowledge.

Important information for the correct installation and for maintenance, that

does not cause any damage.

Denotes that a hazard exists which can result in injury or death if proper

precautions are not taken.

Denotes a reminder of safety practices or directs attention to unsafe practices

which could result in personal injury or damage to the craft or components

or to the environment.

CAUTION

WARNING

DANGER

NOTICE

LEGEND

m.p.h. = miles per hour
km/h = kilometres per hour

10 m.p.h. = 8,69 knots
10 m.p.h. = 16,1 km/h
10 knots = 11,5 m.p.h.
10 knots = 18,5 km/h
10 km/h = 6,21 m.p.h.
10 km/h = 5,4 knots

Summary of Contents for ND1-MM









































Search results

Summary of Contents for ND1-MM

Reviews:

Related manuals for ND1-MM

Brands by name

Popular brands

Ultraflex ND1-MM, Installation Manual

Search results

Summary of Contents for ND1-MM

Reviews:

Related manuals for ND1-MM

Brands by name

Popular brands