Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most
installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during
the activation of the remote starter. Never disconnect or alter the switch to be always bypassed. Always use a
“M
” Series Remote Starter on a manual transmission vehicle.
Never
install an automatic Remote Starter model into a manual transmission vehicle. It is not recommended
to install a remote starter on a convertible type vehicle. If doing so It is highly recommended that a radar
sensor is installed to cover the proximity of the gear shift lever. If the radar sensor is tripped the remote starter
will exit Reservation Mode.
To enter Reservation Mode, the following steps must be followed.
Step 1
- While the vehicle is running, place the transmission in neutral and apply the parking brake.
Step 2
- Press and release the brake pedal. The park lights will activate.
Step 3
- Turn the ignition key off and the vehicle will stay running.
Step 4
- Exit the vehicle and close the door. The vehicle will then shut off*.
Step 5
- The vehicle can now be safely remote started.
* If the vehicle has a dome light delay, the vehicle may stay running until the dome light turns off. This is
normally no longer than 30 seconds.
Reservation Mode will automatically be exited if the doors of the vehicle
are opened. The set-up mode will then have to be repeated. Reservation Mode Must be set-up each time the
vehicle is parked.
Note: If the vehicle is not in Reservation Mode and the Start button is pressed, the system will flash
the park lights four times slowly.
Press Once to Lock / Unlock Doors and arm/disarm the alarm.
Press 2nd Time (within 3 sec.)& Hold for Constant Lock Output.
Press and hold for 3 seconds to activate Trunk Release / Aux Output
Press Once for Start - (
2 Times if programmed for Safety Start
)
Press and hold for 3 seconds while running to turn off
While running with the key, press the button to activate Idle Mode
Press and Release for Status Check
Hold for 3 seconds to enter User Programmable Features
Press both buttons for 3 seconds to activate Car Finder Mode
Transmitter Operation
Reservation Mode - Manual Transmission.
1
- Within three seconds turn the ignition Key ON-OFF-ON-OFF-ON -
Leaving Key ON
2
- Press and hold the Program Button - Parking Lights will come ON
**if the park lights do not come on at this point, turn the key off for 5 seconds, the repeat step 1.
3
- Continue to hold the Program Button until park lights go out.
4
- Press button 1 on the remote transmitter (ensure the “
#
” symbol is not displayed on the LCD)
the park light will flash to confirm transmitter programming.(The ”
#
” symbol is for Dual Car Mode)
Dual car operation:
Enter the User Programming Mode on the second remote and turn the “
#
” symbol on.
Program the remote (Step 1-4) After the 1st remote is programmed press button 1 on the 2nd.
Note:
Transmitter programming must done quickly. Do not pause more than one second between each
transmitter.
All the transmitters
to be used must be programmed at the same time.
All transmitters not
programmed at this time will be erased from memory for security. The system holds a maximum of 4
transmitter codes including 2nd car remote codes.
ACTIVATING Service Mode (Valet)
1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights
will flash five times and the horn (optional)will honk five times to confirm that the system is in
Service Mode.
2. While in Service Mode the remote start functions will be disabled and LED’s will be “ON”
steady. Door locks and trunk release are still operational.
DEACTIVATING Service Mode (Valet)
1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights
will flash two times and the horn (optional)will honk two times to confirm that the system has
exited Service Mode.
2. Remote start functions will return to normal operation.
Transmitter Programming
System Service Mode
System Service Mode (Valet) - By Remote
ACTIVATE Service Mode (User Programmable Feature)
1 - Press and hold button 4 for 3 seconds. (The remote will beep twice)
2 - Press button 1 Five times or until the
?
starts flashing on the LCD screen.
3 - Press button 3 and the
?
symbol will come on solid.
4 - Press button 4 to exit User Program Mode.
(System Is Now In Service Mode)
DEACTIVATE Service Mode
1 - Press and hold button 4 for 3 seconds. (The remote will beep twice)
2 - Press button 1 Five times or until the
?
starts flashing on the LCD screen.
3 - Press button 2 and the
?
symbol will turn off.
4 - Press button 4 to exit User Program Mode.
(Serice Mode is Deactivated)
10
11
1
2
3
4
1
2
3
4
2&3
When the Battery Icon on the remote indicates that the battery is low the battery should be changed
promptly. Replace with quality 1.5volt “AAA” battery.
Battery Replacement
1
Lift
Slide
+
-
PROGRAM MODE 4 - TACH SETTINGS
Setting 1- Method 2- Low Idle Learn
Setting 2- Adjust For Over-Crank
Setting 3- Adjust For Under-Crank
Step 1 - Enter Program Mode
(Ignition ON-OFF-ON-OFF-ON) then press the Program Button on the antenna 1 time.
Step 2 - Enter Program Menu 4 -
Press the
#
button on the remote.(
Button #4
).
Step 3 - Start Vehicle -
Using the ignition key, make sure not to turn the key off at any time or your will exit programming.
Step 4 - Press the Button -
One time
(Led will start flashing in single cycles) then press and hold Program Button for(5sec).
Step 5 - Release the Button -
Led should come on steady to indicate correct tach signal the park light will flash to confirm.
Step 1 - Enter Program Mode
(Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Menu 4 -
Press the
#
button on the remote.
(
Button #4
).
Step 3 - Press the Program Button -
2 times
(Led will start flashing 2 times).
Step 4 - Hold the Program Button -
For 5 seconds until park lights flash (each time lights flash the setting is reduced).
Step 5 - Release the Button - Exit Program Mode and remote start to test.
Step 1 - Enter Program Mode
(Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Mode 4 -
Press the
#
on the remote.(
Button #4
).
Step 3 - Press the Program Button -
3 times
(Led will start flashing 3 times).
Step 4 - Press and Hold Program -
For 5 seconds until park lights flash (each time lights flash the setting is increased).
Step 5 - Release Program - Exit Program Mode then remote start to test.
