Installation Guide
PROGRAMMING
8
1 Double Pulse Unlock
1 Flash
Single .75sec.Lock pulse and double Unlock Pulse
2 3 Second Lock & Unlock
2 Flashes
3 second pulses for Lock & Unlock
*3 0.75 Second Pulses
3 Flashes 0.75 second pulses for Lock and Unlock
1 Ignition Lock & Unlock Enabled
1 Light Flash
Doors Lock / Unlock when the key is turned On/ Off
2 Ignition Lock Only
2 Light Flashes
Doors Lock when ignition key is turned ON only
*3 Ignition Auto Lock Disabled
3 Light Flashes
Doors do not Lock or Unlock with Ignition key
1 Lock & Unlock chirps
Disabled
1 Flash
Honks for Panic and Car Finder Mode only.
2 Lock & Unlock chirps
Enabled
2 Flashes
Honks for Lock, Unlock, Panic and Car Finder Mode Only.
*3 All chirps enabled
3 Flashes
Honks for Lock, Unlock, Start, Panic and Car Finder Mode.
Press the Program Switch 1 time
to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program
Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch.
Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 2 times
to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program
Switch until you receive the appropriate # of park light flashes and/or horn honks
Release the Program Switch.
Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 3 times
to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program
Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch.
Press the Program momentarily to move to next program step or repeat to change selection.
Setting 1- Ignition Auto Lock
Setting 2- Horn Honk Settings
Setting 3- Door Lock Options
PROGRAM MODE - TACH SETTINGS
Setting 1- Method 2- Low Idle Learn
Setting 2- Adjust For Over-Crank
Setting 3- Adjust For Under-Crank
PROGRAM MODE - USER SETTINGS
Step 1 - Enter Program Mode
(Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Mode 4 -
Press the
#
button on the remote.(Button #4).
Step 3 - Start Vehicle -
Using the ignition key, make sure not to turn the key off at any time or your will exit programming.
Step 4 - Press the Program Button -
One time (Led will start flashing in single cycles) then press and hold Program
Button for (5sec).
Step 1 - Enter Program Mode
(Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Mode 4 -
Press the
#
button on the remote.
(Button #4).
Step 3 - Press the Program Button -
2 times
(Led will start flashing 2 times).
Step 5 - Release Program - Exit Program Mode and remote start to test.
Step 4 - Press and Hold Program -
For 5 seconds until parking lights flash (each time lights flash tach is reduced 5%).
Step 1 - Enter Program Mode
(Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Mode 4 -
Press the
#
on the remote.(Button #4).
Step 3 - Press the Program Button -
3 times
(Led will start flashing 3 times).
Step 5 - Release Program - Exit Program Mode then remote start to test.
Step 4 - Press and Hold Program -
For 5 seconds until parking lights flash (each time lights flash tach is increased 5%).
Enter USER SETTINGS - Program Mode - See Page 7 for details on entering program mode
This option is used for vehicles that maintain a HIGH or erratic idle after starting and need more that 10
seconds to establish a stable idle.
See page 6 for Auto Tach Learning