Ultra Start 1500 SERIES, Installation Manual

Page: 2 / 12

Installation Guide
1500 Wiring Diagram Page 3
Page 5
Page 6-7
Pre-Installation Page 4
What’s Included
Pre Installation Check
Installation Procedures
Wire Connectors
6 Pin Connector
14 Pin Connector
4 Pin Red Connector
Jumper Settings
Installation
Basic Installation - Quick start
Under Hood Connections
Installing The Antenna
Mounting The Module
Operating The System
Programming Page 7-9
Program Overview & System Reset
Program Menu 1 (User Settings)
Program Menu 3 (Starter Settings)
Program Menu 4 (Tach Settings)
Operations Page 10
Single & Dual Car Operation
Timer Mode
Manual Transmission (Reservation Mode)
Additional Operations Page 11
1st & Second Car Transmitter Programming
Battery Replacement
Emergency System Service Mode
Relay Diagrams Page 12
TABLE OF CONTENTS
If the remote starter has a failed start attempt or if a safety input is activated the Diagnostic Memory will
store up to four shutdowns in memory. This information can then be accessed to determine the source of
the shutdown.
To Enter Diagnostic Mode:
Step 1 - Turn the ignition on wait two seconds then turn off. Press the Program Button and release.
Step 2 - The system will respond with three park light flashes and the horn will honk (optional) the
same number of times as the events in memory. ( Maximum four events, four honks)
NOTE: If the horn does not honk, there are no events in memory.
Step 3 - Press the Program Button once to view the last shut down code. The (optional) Horn will
honk once to confirm code one.
Step 4 - The LED’s on the antenna will flash a code corresponding to a shut down trigger. Press the
Program Button again to check the second code. The horn will honk twice to confirm code two.
Step 5 - To Clear Diagnostic Memory. While in Diagnostic Mode press and hold the Program Button for
five seconds. The park lights will flash and the horn(optional) will honk once.
NOTE: Once diagnostic memory has 4 shutdown events in memory, the system will not record any
further shutdown events until the system memory has been cleared.
(If the horn does not honk, there are no codes in memory).
PARK LIGHTS STATUS LED DIAGNOSTIC CODE
3 Flashes Series of 3 Flashes Door Opened “M” Models
3 Slow Flashes No Flashes Start Attempt In Service Mode(Valet)
4 Flashes No Flashes Hood/Brake Triggered Before Start
4 Slow Flashes Series of 4 Flashes Not in Reservation Mode “M” units
5 Flashes Series of 5 Flashes Hood Pin Grounded (Open)
6 Flashes Series of 6 Flashes Brake Pedal Shutdown
7 Flashes Series of 7 Flashes Tach Lock-Out
PARK LIGHTS STATUS LED DIAGNOSTIC CODE
3 Flashes Series of 3 Flashes Door Opened “M” Models
3 Slow Flashes No Flashes Start Attempt In Service Mode(Valet)
4 Flashes No Flashes Hood/Brake Triggered Before Start
4 Slow Flashes Series of 4 Flashes Not in Reservation Mode “M” units
5 Flashes Series of 5 Flashes Hood Pin Grounded (Open)
6 Flashes Series of 6 Flashes Brake Pedal Shutdown
7 Flashes Series of 7 Flashes Tach Lock-Out
PARK LIGHTS STATUS LED DIAGNOSTIC CODE
3 Flashes Series of 3 Flashes Door Opened “M” Models
3 Slow Flashes No Flashes Start Attempt In Service Mode(Valet)
4 Flashes No Flashes Hood/Brake Triggered Before Start
4 Slow Flashes Series of 4 Flashes Not in Reservation Mode “M” units
5 Flashes Series of 5 Flashes Hood Pin Grounded (Open)
6 Flashes Series of 6 Flashes Brake Pedal Shutdown
7 Flashes Series of 7 Flashes Tach Lock-Out
DIAGNOSTICS DIAGNOSTICS DIAGNOSTICS
2
1
3
5
2
4
6
2
1
4
3
6
5
7
8
10
9
12
11
14
13