Ultimate GHARGER PRO-8 User Manual Download Page 12

10

Discharging

Always refer to the manual by the battery manufacturer pertaining to charging methods,
recommended charging current and charging time.Especially,the Lithium battery should 
be charged according the charging instruction provided by the manufacturer strictly.

Attention should be paid to the connection of Lithium battery especially.

Do not attempt to disassemble the battery pack arbitrarily.

Please get highlighted that Lithium battery packs can be wired in parallel and in series.
In the parallel connection,the battery's capacity is calculated by multiplying single 
battery's capacity by the number of cells with total voltage stay the same.The voltage's
imbalance may cause fire or explosion.Lithium battery is recommended to charge in series.

The main purpose of discharging is to clean residual capacity of the battery,or to reduce the 
battery'voltage to a defined level.The same attention should be paid to the discharging process 
as charging.The final discharge voltage should be set up correctly to avoid deep-dischargeing.
Lithium battery can not be discharged to lower than the minimum voltage,or it will cause a 
rapid loss of capacity or a total failure.Generally,Lithium battery doesn't need to be discharged.
Please pay attention to the minimum voltage of Lithium battery to protect the battery.

Some rechargeable batteries have a memory effect.If they are partly used and recharged before 
the whole charge is accomplished,they remember this and will only use that part of their 
capacity next time.This is a "memory effect" it is said that NiCd and NiMH batteries are 
suffering from memory effect.NiCd has more memory effect than NiMH.

Lithium batteries are recommended to be discharged partially rather than fully discharged.
Frequent full discharging should be avoided if possible.Instead,charge the battery more often 
or use a battery of larger capacity.Full capacity cannot be used until it has been subjected to 
10 or more charge cycles.The cyclic process or charge and discharge will optimize the 
capacity of battery pack.

GHARGER PRO-8

Summary of Contents for GHARGER PRO-8

































Reviews: