background image

www.U-LineService.com

6

11/2006

CO1175 — Ice Maker/Refrigerator

Reversing the Door

(CO1175 Black Units Only)

All units may be left-or right-hand opening (All Stainless 
Steel units cannot be field-reversed).

Black Units

Note: 

The grille should not yet be installed. If it has been 

installed, remove it for door reversing. See 

Page

 

11

.

To reverse the door on Black models:

1. Remove top hinge from cabinet (four screws). See 

Figure 4

. Hold door to keep it from falling.

2. Lift the door off the bottom hinge.

3. Remove four plastic plugs in hinge holes, top of cabinet, 

opposite side. See 

Figure 5

.

 

Be careful not to scratch 

cabinet.

4. Remove pivot screw from top hinge, invert screw and 

reinstall pivot screw in top hinge. See 

Figure 6

. Do not 

install hinge on cabinet at this time.

5. Remove bottom hinge from cabinet (four screws) and 

screws on opposite side of cabinet. See

 

Figure 7

.

6. Remove pivot screw from bottom hinge, invert screw 

and reinstall pivot screw in hinge. See 

Figure 6

.

7. Install bottom hinge on cabinet, opposite side, aligning 

flat edge of hinge with outer edge of unit. Partially 
tighten screws. See 

Figure 8

.

8. Relocate plastic spacer/bushing on bottom of door to 

the opposite side. See 

Figure 9.

 Clean out bushing hole 

in door bottom if necessary.

9. Place door on lower hinge pin. Align flat edge of top 

hinge with outer edge of unit and fasten upper hinge 
to unit (four screws). Partially tighten screws. See

 

Figure 10

.

10. Adjust door to assure proper seal. Tighten upper and 

lower hinge screws securely. 

11. Replace four plastic plugs removed in Step 4 into holes 

on top of unit. Replace screws in holes in bottom of unit 
on opposite side.

Other Site Requirements

Power Supply

The unit requires a grounded and polarized 115 VAC, 
60 Hz, 15A circuit (normal household current). See 
Electrical Specifications on 

Page

 

10

.

Figure 4

Figure 5

Plastic

Plug Hole

Plastic

Plug Hole

Hinge

Screw

Right Side

Door Swing

Right Side

Hinge

Invert

Screw

Invert
Hinge

Left Side

Door Swing

Figure 6

Figure 7

Figure 8

Bushing

Figure 9

Figure 10

Summary of Contents for Origins CO1175AS














Reviews: