Tuthill KINNEY 850D Operator'S Manual Download Page 3

Page: 3 / 38

1. INTRODUCTION

CONGRATULATIONS

on your purchase of a new

KINNEY

KT™

Single-Stage, Tri-plex Rotary Piston

Vacuum Pump from Tuthill Vacuum & Blower Systems. Please examine the pump for shipping damage, and

if any damage is found, report it immediately to the carrier. If the pump is to be installed at a later date make

sure it is stored in a clean, dry location and rotated regularly. Make sure covers are kept on all openings. If

pump is stored outdoors be sure to protect it from weather and corrosion.

This manual applies to Kinney Vacuum models KT-150, KT-300, KT-500 and KT-850. You should be

thoroughly familiar with these instructions before attempting to install, operate or repair this unit. Consult

Tuthill Vacuum & Blower Systems when problems arise that cannot be resolved after reading this manual.

Always include pump nameplate information when ordering parts or components.

KINNEY KT

vacuum pumps are built to exacting standards and if properly installed and maintained will

provide many years of reliable service. We urge you to take time to read and follow every step of these

instructions when installing and maintaining your pump. We have tried to make these instructions as

straightforward as possible. We realize getting any new piece of equipment up and running in as little time

as possible is imperative to production.

CAUTION

Read manual before operation or bodily harm may result. Attention should

be given to the safety related sections of this manual.

NOTE

Record the model and serial numbers of your machine in the OPERATING

DATA form on the inside back cover of this manual. You will save time and

expense by including this reference identification on any replacement part

orders, or if you require service or application assistance.

1.1 APPLICABLE DOCUMENTATION

The applicable documents associated with this manual are:

• EN 1012-1:1996 - Compressors and vacuum pumps - Safety Requirements - Part 2: Vacuum Pumps

1.2 SCOPE OF MANUAL

The scope of this manual includes the following components as offered by Tuthill Vacuum & Blower Systems:

Rotary Piston Pump

2. CONVENTIONS AND DATA PLATE

2.1 GRAPHIC CONVENTIONS IN THIS MANUAL

This manual is the result of a risk assessment according the applicable documents referenced in section

1.1. The following are hazard levels are referenced within this manual:

DANGER

Indicates an immediate hazardous situation which, if not avoided, will result

in death or serious injury.

Summary of Contents for KINNEY 850D







































Search results

Summary of Contents for KINNEY 850D

Reviews:

Related manuals for KINNEY 850D

Brands by name

Popular brands

Tuthill KINNEY 850D, Operator'S Manual

Search results

Summary of Contents for KINNEY 850D

Reviews:

Related manuals for KINNEY 850D

Brands by name

Popular brands