Tuthill KINNEY 850D Operator'S Manual Download Page 15

Page: 15 / 38

NOTE

Do not block or restrict the flow of gas from the pump discharge. Back

pressure within the pump could cause severe damage.

6.1.1 ELECTRICAL CONNECTIONS

WARNING

Disconnect pump from source electrical power prior to making repairs or

adjustments of any electric component of the unit.

If the pump is not wired when received, wire the motor as per the schematic/label on motor. Also wire any

optional controls prior to start-up. Connect the motor and all applicable electrical accessories to a motor

controller equipped with both overcurrent running protection and short circuit protection.

When wiring is complete turn the pump by hand to ensure that the pump is free to turn and then momentarily

jog the motor to check that the pump rotation direction is clockwise when facing the drive end. If the pump

rotates in the wrong direction reverse any two of the three motor leads. If a flow switch is provided it should

be wired into the motor circuit with a relay so as to stop the motor in the event that the cooling water flow

is interrupted.

Optional custom control panels and electrical accessory components, along with schematic wiring diagrams

and wiring instructions are available separately from Tuthill Vacuum & Blower Systems.

6.2 PRE-START CHECKS

Before starting the pump check the following items:

1. The installation has been made in accordance with the installation section of this manual.

The pump has been filled with oil and the cylinder has been filled with water, in accordance with the

installation section of this manual.

3. If the pump has been idle for a month or more – Turn the pump by hand two or more revolutions to

distribute oil internally through the pump.

4. The temperature of the pump oil is 60°F (16°C) or above. Optional pump heaters are available for

installation in the cylinder water jacket.

Cooling water is available. Do not start the cooling water flow until the pump has operated a few

minutes.

6. Drive belts are correctly tensioned. See

V-Belt Drive

Section.

7. Direction of rotation is correct.

WARNING

Correct rotation is clockwise when viewed from the drive end

(Counterclockwise when viewed from the motor fan). Operating the pump

with the incorrect rotation will cause

FAILURE

WARNING

Physical harm may occur if human body parts are in contact or exposed to

the process vacuum. Assure that all connections are protected from human

contact.

CAUTION

Do not touch hot surfaces. Discharge gas based on operating conditions

can be elevated.

Summary of Contents for KINNEY 850D







































Search results

Summary of Contents for KINNEY 850D

Reviews:

Related manuals for KINNEY 850D

Brands by name

Popular brands

Tuthill KINNEY 850D, Operator'S Manual

Search results

Summary of Contents for KINNEY 850D

Reviews:

Related manuals for KINNEY 850D

Brands by name

Popular brands