Key Beep
Buzzer
N
N
◄
Dec Inc
►
Dec Inc
Completion Ring
Beep alway
Back-light
+
Dec Inc
50%
Cooling fan AU
0
+
◄Dec
Inc►
Dec
Inc
Discharge
reduce
OFF
5
%
+
+
Dec
Inc
Dec
Inc
◄
Dec
Inc
►
LiFe Termination
Voltage
3.60V
◄
Dec
Inc► ◄Dec Inc►
Lile Termination
Voltage
4.1 0V
+
◄
Dec Inc
►
◄Dec
Inc
►
LiPo Termination
Voltage
4.20V
◄
Dec
Inc
►
◄Dec
Inc
►
!
.
+
Pd Termination
Voltage
2.40V
◄Dec Inc►
Key confirmation and alen tone. lf1he keyboard sound is ON there will be a beep when
you press any key. If 1he bu1.zer 1s ON the charger \viii generate an al en tone for certain
Key Deep: OFF&ON:(ON, dd3ult)
lluzzer: OFF&ON:(ON, default)
Process completion tone. Controls the tones gen�rated at end of charging or discharging
and the cyclic charging/discharging indication.
Options: Beep 5 times, Be.:-p 3 minutes, Beep always (continuous until user presses
STOP), Beep OFF
(Beep always, default)
Back-light and cooling fan control. Adjust the LCD backlight brigh1ness. There are three
cooling fan modes: ON, OFF, AUTO. In AUTO-Mode, the charger adjusts the fan
automatically to control its internal temperature.
Cooling fan: OFF, ON & AUTO (AUTO, default)
Discharge reduce sening. When you set it to �oN• , if the final voltage target storage
voltage is reached, the buzzer will beep for three times, and the left of the second line
display "D> > • , and the charger enters into the high precision discharge process. The
process won' t stop until the current reaches xx % of the configured discharge current.
Reduce:ON,OFF Range: 1-99%
Termination voltage for LiFe. Adjust LiFe' s charge termination voltage. Press
Start/Enter for more than 3 seconds to blink the "Voltage• value, t
hen p
r
e
ss
◄
Dec
and
Inc►
to adjust the termination voltage.
Range: 3.40V-3.90V, Step: 0.0IV(3.60V, default)
Termination voltage for Lilo. Adjust Li\o' s charge termination voltage. Press
Start/Enter
for more than 3 seconds 10 blink the "Voltage• value, then press
◄
Dec
and
Inc►
to adjust the 1ermination voltage.
Range: 3
.
90V
--l
.
20V, Step: 0.0IV(4.I0V,default)
Termination voltage for Li Po. Adjust Li Po's charge termination voltage. Press
Start/Enter
for more than 3 seconds to blink the "Voltage• value, then
press
◄Dec
and
Inc►
to adjust the termination voltage.
Range: -l.OOV-4.30V, Step: 0.QJ V(-l.20V, defauh)
Termination voltage for Pb. Adjust Pb's charge termination voltage. Press
Start/Enter
for more than 3 seconds to blink the "Voltage• value, then press
◄
Dec
and
Inc ►to
adjust the termination voltage.
Range: 2.WV-2.SOV, Step: 0.0IV(1.40V, default)
Note: The Termination voltage controls the transition from Constant Current (CC) to
Constant Voltage (CV) charging for LiXx and Pb chemistries. It also defines the per-cell
limil for cell overvoltage detection.
If you change the default termination voltage, the charge and discharge setting screen
will note this difference by alternatively blinking battery's type and setting voltage value.
8
