Turbosol Beton Master Operation And Maintenance Manual Download Page 39

 

 

MAINTENANCE 

 

561270 - IS19/07 - EN

 

39/58 

 

8    -    MAINTENANCE 

8.1 

MAINTENANCE TO BE CARRIED OUT BY OPERATOR 

 

 

 The following are the basic instructions for performing proper maintenance on the machine. More detailed 

information  can  be  found  in  the  diesel  engine  operation  and  maintenance  manual  (supplied),  which 
operators are required to read and understand (along with the present manual) before using the machine. 

 

CHECKING THE LUBRICATION WATER LEVEL 

- Open the discharge lever (FIG. 43-REF. 1) to empty the tank. 
-  If  the  water  in  the  tank  is  not  clear  but  grey  and  thick,  it  means  that  slurry  is  seeping  out  from  between  the  piston  and  the 
pumping tube. If this occurs, replace the pistons. 
- Turn the lever (FIG. 43-REF. 1) to its horizontal position to close the tank. 
- Fill the tank by pouring water through the slots until overflowing. 
 

1

21

21

21

 

FIG.43                                                                                               FIG.44 
 

 

 

 The  lubrication  water  should  be  changed  completely  at  least  once  a  week,  or  preferably  after  every  work 

session. 

 

 

 When working in a cold climate, empty the tank at the end of every work session or add antifreeze. 

 

CHECKING THE ENGINE COOLANT LEVEL 

Check the level of the engine coolant and top up if necessary (see paragraph 7.3). 
 

CHECKING THE MOTOR OIL 

Check the motor oil level using the dipstick. The level should be near the top mark but never above. 
For topping up, use: TOTAL RUBIA TIR 7400 or an equivalent oil. 
 

CHECKING THE ENGINE AIR FILTER 

The engine air filter contains two filter cartridges (1st and 2nd stage). To inspect the filter snap off the cover (FIG. 44-REF. 1) 
and remove the 1st stage cartridge (FIG. 44-REF. 2) and the 2nd stage cartridge (FIG. 44-REF. 3). Lightly tap the filter element 
of the 1st stage cartridge on a hard surface a few times to shake off any excess dirt. Do not blow the paper filter element with 
compressed  air.  The  2nd  stage  cartridge  can  be  cleaned  a  few  times  with  compressed  air  but  not  washed  with  water. 
Accurately clean the cover and the filter mount. 
 

CHECKING THE DIESEL FUEL LEVEL 

Check the diesel fuel level. 

Summary of Contents for Beton Master



























































Reviews: