Optional Equipment 44
Optional Equipment Cont’d
Outrigger Kit
Figure 12
MVT1710, MVT1712,
MVT1713, MVT1715
Part Number T-70316MVT
T-70318MVT
Ref.# Part #
Description
Qty.
1
12163
HEX BOLT, 1/2” X 3 1/2” GR. 5
4
2
T-OR2
OUTRIGGER HALF
4
3*
T-OR1
OUTRIGGER WASHER, 1 1/8”
*Note
4
T-26
HEX NUT, 1/2”
4
5
T-25
LOCK WASHER, 1/2”
4
6
T-760
HEX BOLT, 3/4” X 3 1/2” GR. 5
2
7
181381
DISK BLADE, 18” X 1” PLAIN for 22”
2
8
T-1
END WASHER, 1 1/8”
2
9
T-723
FLAT WASHER, 3/4”
2
10
T-31
LOCK WASHER, 3/4”
2
11
T-27
HEX NUT, 3/4”
2
*Note: Item #3, Part# T-OR15 is not included with this assembly. The T-OR15 is standard
equipment on the rear gangs of the MVT series.
Outrigger Kit Mounting Instructions
Reference Figure 12
Outrigger kits only attach to rear gang with out-
rigger washers (Ref. #3). Outrigger washers
DO NOT come with kit. They are standard
equipment on rear gangs of the
MVT
series. To
attach outriggers, remove cast iron end washer
(Ref. #8), 3/4” flat washer (Ref. #9), 3/4” lock
washer (Ref. #10), and 3/4” hex nut (Ref. #11)
from 3/4” x 3 1/2” Gr. 5 bolt (Ref. #6). Remove
1/2” hex nuts & lock washers (Ref. #4 & #5)
from 1/2” x 3 1/2” Gr. 5 bolts (Ref. #1). Take
outrigger halves (Ref. #2) and pull apart wide
enough to clamp over outrigger washer (Ref.
#3) on gang assembly. Re-apply the 1/2” hex
nuts & lock washers (Ref. #4 & #5) to 1/2” x 3
1/2” Gr. 5 bolt (Ref. #1) and tighten. Make sure
the 3/4” x 3 1/2” Gr. 5 bolt (Ref. #6) is pulled out
as far as possible before tightening. Once tight-
ened, apply the outrigger disk blade (Ref. #7)
on the 3/4” x 3 1/2” Gr. 5 bolt (Ref. #6), followed
by the cast iron end washer (Ref. #8), 3/4” flat
washer (Ref. #9), 3/4” lock washer (Ref. #10),
and 3/4” hex nut (Ref. #11). Tighten and outrig-
ger is ready for operation. Please see Bolt
Torque Chart (Page 45) for proper torque infor-
mation.
*NOTE-
MVT
models use 18” outrigger blades
for 22” disk blades.
*NOTE- Retighten all fasteners after first opera-
tional use. Please see Bolt Torque Chart (Page
45) for proper torque information.
Summary of Contents for MVT1710
