TSC TTP-2410MT Series User Manual Download Page 42

Page: 42 / 87

- 35 -

4.3 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles

This printer has been fully tested before delivery. There should be no ribbon wrinkle presented on the

media for general-purpose printing application. Ribbon wrinkle is related to the media thickness, print

head pressure balance, ribbon film characteristics, print darkness setting…etc. In case the ribbon wrinkle

happens, please follow the instructions below to adjust the printer parts.

Adjustable

Printer

Parts

The print head pressure adjustment knob has 5 levels of settings. Clockwise direction
adjustment is to increase the print head pressure. Counter Clockwise adjustment can
decrease the print head pressure.

Symptom

1. Wrinkle happens from label lower

left to upper right direction (“

”)

2. Wrinkle happens from label lower

right to upper left direction (“

”)

Wrinkle

Example

Feed direction

Z-axis mechanism
adjustment knob

Print head pressure
adjustment knob

Summary of Contents for TTP-2410MT Series
























































































Search results

Summary of Contents for TTP-2410MT Series

Reviews:

Related manuals for TTP-2410MT Series

Brands by name

Popular brands

TSC TTP-2410MT Series, User Manual

Search results

Summary of Contents for TTP-2410MT Series

Reviews:

Related manuals for TTP-2410MT Series

Brands by name

Popular brands