TSC TTP-2410MT Series User Manual Download Page 4

Page: 4 / 87

- iii -

Wichtige Sicherheits-Hinweise

1. Bitte lesen Sie diese Hinweis sorgfältig durch.

2. Heben Sie diese Anleitung fűr den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromentz zu trennen. Verwenden Sie keine Flüssig-oder

Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung.

4. Die Netzanschluß -Steckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schűtzen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte

Beschädigungen hervorrufen.

7. Beachten Sie beim Anschluß ans Stromnetz die Anschluß werte.

8. Dieses Gerät kann bis zu einer Auß entemperatur von maximal 40

℃

betrieben werden.

CAUTION

Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

“VORSICHT”

Explosionsgefahr bei unsachgemäß en Austaush der Batterie. Ersatz nur durch denselben oder

einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angabren
des Herstellers.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the
user's authority to operate the equipment.

CAUTION

1. HAZARDOUS MOVING PARTS IN CUTTER MODULE. KEEP FINGER AND OTHER

BODY PARTS AWAY.

2. THE MAIN BOARD INCLUDES REAL TIME CLOCK FEATURE HAS LITHIUM BATTERY

CR2032 INSTALLED. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE.

3. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER

INSTRUCTIONS.

Summary of Contents for TTP-2410MT Series
























































































Search results

Summary of Contents for TTP-2410MT Series

Reviews:

Related manuals for TTP-2410MT Series

Brands by name

Popular brands

TSC TTP-2410MT Series, User Manual

Search results

Summary of Contents for TTP-2410MT Series

Reviews:

Related manuals for TTP-2410MT Series

Brands by name

Popular brands